699031
20
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
18 Installer Manual SATEL
5.6.1 Connecting the INT-VG or INT-AV module or CA-64 SM expander
When connecting the INT-VG voice module, INT-AV audio alarm verification module or the
CA-64 SM voice synthesizer expander, the CLK and DTA wires only are to be connected to
the bus. Each of these devices is additionally provided with the PIN5 connector, which should
be inserted into the control panel onboard socket designated as SYNT1 or SYNT2.
Only one INT-VG module or CA-64 SM expander can be connected to the
INTEGRA 64 Plus control panel, because it allows not more than 16 voice messages
to be played back.
5.6.2 Addressing devices connected to the expander bus
Each device to be connected to the expander bus must have its own individual address from
the 0 to 31 range. The addresses of devices connected to the same bus must not repeat (the
control panel does not support devices having identical addresses). It is recommended that
consecutive addresses be assigned starting from 0. In most devices, the address is set by
means of DIP-switches.
If the device is connected to the second bus, its address in the system can be
determined by adding the number 32 to the address set in it.
The address affects numeration of zones and outputs in the system (see section
NUMERATION OF ZONES AND OUTPUTS IN THE SYSTEM p. 28).
5.7 Connecting the detectors
How the detector is connected to the zone must be suitable for the configuration chosen for
that zone. The zones on the control panel mainboard support the following configurations:
NC the wiring type dedicated to connecting devices with the NC (normally closed) alarm
output. Opening the circuit will trigger an alarm.
NO the wiring type dedicated to connecting devices with the NO (normally open) alarm
output. Closing the circuit will trigger an alarm.
EOL this wiring type may be used to connect devices having the NC or NO alarm output.
Closing or opening the circuit will trigger an alarm.
2EOL/NC the wiring type recommended to connect detectors having the NC alarm output
and a tamper output. The zone can recognize 3 states: normal, alarm and tamper.
2EOL/NOthe wiring type similar as 2EOL/NC, but for detectors with the NO alarm output.
Roller the wiring type dedicated to connecting roller shutter detectors.
Vibration the wiring type dedicated to connecting vibration detectors. The zone will also
accept connection of a detector with the NC alarm output (e.g. a vibration detector and
a magnetic contact can be connected in series).
Follow output in case of this configuration the detector should not be connected. The zone
status depends only on that of the selected output (the output is not to be physically
connected to the zone).
Roller 2EOLthe wiring type similar as 2EOL/NC, but for the roller shutter detectors.
Vibration 2EOL the wiring type similar as 2EOL/NC, but for the vibration detectors.
3EOL/NCthe wiring type recommended for connecting detectors with the NC alarm output,
tamper output and anti-masking output. The zone can recognize 4 states: normal,
alarm, tamper and masking of detector.
3EOL/NO the wiring type similar as 3EOL/NC, but for the detectors with the NO alarm
output.
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satel Integra 256 Plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satel Integra 256 Plus

Satel Integra 256 Plus Bedienungsanleitung - Deutsch - 55 seiten

Satel Integra 256 Plus Zusatzinformation - Deutsch - 108 seiten

Satel Integra 256 Plus Installationsanweisung - Deutsch - 36 seiten

Satel Integra 256 Plus Bedienungsanleitung - Englisch - 51 seiten

Satel Integra 256 Plus Zusatzinformation - Englisch - 102 seiten

Satel Integra 256 Plus Kurzanleitung - Holländisch - 2 seiten

Satel Integra 256 Plus Zusatzinformation - Holländisch - 108 seiten

Satel Integra 256 Plus Bedienungsanleitung - Holländisch - 53 seiten

Satel Integra 256 Plus Installationsanweisung - Holländisch - 35 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info