Bedienungsanleitung Satel Integra 256 Plus (Seite 27 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

SATEL INTEGRA Plus 25

Wait aft.disc.

Runtime

No autorst.3t.

Tamper in part.

2.6 Entering data by means of the keypad

Data are saved to the control panel if you press the key (in some keypads, the key is

also available, whose function is exactly the same). The key enables exiting the function

without saving any changes.

Described below are general rules for entering data, however they may be different as

regards some functions.

2.6.1 Selection from the single-choice list

The upper line of display shows the function name, and the lower one – the currently

selected item. To scroll through the item list, use the  keys (down) and the  keys (up).

The  and  keys are not used.

2.6.2 Selection from the multiple-choice list

The functions that allow you to make multiple choice can be identified by an additional

symbol situated at the right-hand side of the display:

– displayed item is selected / option is enabled,

– displayed item is not selected / option is disabled.

Pressing any digit key (for some functions, this does not work with the key 0) will change the

currently displayed symbol to the other one. To scroll through the list of items, use the  key

(down) or the  key (up). For some functions, pressing the key 0 will allow you to enter the

number of item to be edited (e.g. the number of partition or zone). This will speed up search.

For some functions, pressing the  or  key will switch the keypad into the graphic

programming mode. The and symbols are used to present on the display the current

status of up to 32 items available in the given function (these can be e.g. zones, outputs,

timers, etc.). The  key moves the cursor to the right, and the  key to the left. If the list of

items is longer than 32, pressing the  key when the cursor is placed over the last item will

display the next list, and pressing the  key when the cursor is placed over the first item will

display the previous list. Pressing the key 0, 1 or 2 three times in the graphic mode within 3

seconds will have the following effect:

000 - the symbol will be displayed at all available items,

111 - the symbol will be displayed at all available items,

222 - reversal of the selection made: the symbol will be displayed at all items where

the symbol was displayed, and the symbol where the symbol was displayed.

On pressing the  or  key, the keypad will return to the text mode.

2.6.3 Entering decimal and hexadecimal values

Digits are entered by pressing the suitable keys. Characters from A to F are available under

the keys with numbers 2 and 3. Keep pressing the keys until the required character appears.

2.6.4 Programming telephone numbers

Keep pressing particular keys until the required character appears. Characters available in

the keypad are presented in Table 1. Up to 16 characters can be programmed. Some of the

special characters (a, b, c, d, # and ) are coded so that the character takes up two items,

hence the maximum number of characters available for entering, if they are used, will be

lower.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info