Bedienungsanleitung Satel Integra 256 Plus (Seite 33 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

SATEL INTEGRA Plus 31

Configuring the modem connected to computer

You can edit the parameters after clicking on the “Change” button.

Port RS-232 – computer COM port to which the modem is connected.

Modem – list of modems, the parameters of which are defined. The list of modems and their

settings will be written to disk in the “modem.ini” file.

Baud Rate – transmission rate of the serial port. It is recommended that the highest rate

acceptable by the modem be set (only some modems may require the 300 bps setting in

order to enforce operation with exactly this speed).

Reset command – the command to reset the modem. Typically, it is the ATZ command

(reset with restoration of the user's zero profile). Some modems may require using the

AT&F command (reset with restoration of the factory default settings).

Initializing – lines containing the modem initialization commands:

for communication with built-in control panel 300 bps modem: in the first line E0V1Q0

– a command required for proper operation of the modem. You should also add the

operating mode selection: B0 or B1 (selection of transmission format: V.21 or Bell103),

and the commands limiting transmission rate over telephone line to 300 bps. These are

commands specific for the given modem model, e.g. N0S37=3, F1 or +MS=1,0,300,300

etc. Information on how to limit the modem transmission rate is usually included in the

device manual. The other line should contain the following commands:

S0=0S9=1S7=120S10=255. They are necessary for correct operation.

for communication with external analog modem connected to the control panel: in

the first line E0V1Q0, the second line S0=0S7=120. It is not recommended to insert

additional commands to limit the modem transmission rate, unless this is required by

the modems used, or the telephone link quality.

for communication through ISDN or GSM modem: in the first line E0V1Q0, the second

line S0=0. Depending on the modems used, you will have to use additional

commands to set the identical transmission format, as in the control panel

modem, i.e. specific for the given modem. V.110 format is intended for the GSM

modems.

Modem ISDN – enable this option, if communication is to be effected through an ISDN or

GSM modem.

3.2.3 Ethernet communication parameters

Programming the parameters

Control panel settings

Settings related to working in conjunction with the Ethernet module which enables

communication over Ethernet can be configured when programming the telephone options

(see: “Telephone options” p. 68).

Ethernet module settings

For description of the configuring, please refer to the Ethernet module manual.

DLOADX program settings

The settings for communication using the ETHM-1 Plus / ETHM-1 module can be configured

in the “Connection settings” window (the command for opening this window is available in the

“Communication” menu; you can also use the Ctrl+R key combination).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info