Bedienungsanleitung Satel Integra 256 Plus (Seite 48 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

46 Programming SATEL

dependent “AND” type of partition will be armed when all indicated partitions are armed

(start of the procedure of arming the last of the indicated partitions will initiate the

procedure of arming the dependent partition). The dependent “AND” type of partition will

be disarmed when any of the indicated partitions is disarmed. This type of partition is

recommended in case of shared corridors.

Follow type “OR” [Dependent “OR”] – the partition controlled by status of other partitions.

You should indicate the partitions whose status affects the dependent partition. The

dependent “OR” type of partition will be armed when any of the indicated partitions is

armed (start of the procedure of arming any of the indicated partitions will initiate the

procedure of arming the dependent partition). The dependent “OR” type of partition will be

disarmed when all indicated partitions are disarmed.

Access according to timer 1...32 [Acc. by t. 1..32] / Access according to timer 33...64

[Acc. by t.33..64] – the partition can be armed/disarmed by the user, but only within the

time intervals set by the indicated timers.

Controlled by timer 1...32 [Tim. 1..32 ctrl] / Controlled by timer 33...64 [Tim. 33..64 ctrl] –

the partition, which is armed in time periods determined by selected timers, but may also

be controlled by the user code.

Bank vault – the partition can be armed / disarmed by the user. Disarming may be delayed

by a defined period of time (see: DISARM DELAY). After it has been disarmed, the partition

can be automatically re-armed after a defined period of time elapses (see: TIME TO RE-

ARM).

Times

Partition exit delay – the time counted from the start of the procedure of arming (by the

user, timer, zone, etc.), which allows to leave the protected area without triggering an

alarm.

Auto-arming delay [Auto-arm delay] – the time counted before starting the procedure of

arming by timer. It allows the user to postpone or cancel the auto-arming.

Alarm verification time [Al. verify time] – the time counted from the triggering alarm by

a zone included in alarm verification (with enabled PRE-ALARM or WITH VERIFICATION

option). If during the count another zone included in the alarm verification triggers an

alarm, a verified alarm will be triggered.

Guard round (on armed) every [Guard - armed] – the maximum period of time that can

elapse since the last guard round when the partition is armed. If the time is exceeded,

information about the lack of guard round will be saved to the control panel memory.

Programming the value 0 will disable the control of guard round.

Guard round (on disarmed) every [Guard - disarm.] – the maximum period of time that can

elapse since the last guard round when the partition is disarmed. If the time is exceeded,

information about the lack of guard round will be saved to the control panel memory.

Programming the value 0 will disable the control of guard round.

Blocked for guard round [Time for guard] – the time counted from the moment of

registering the guard round, during which the partition is blocked.

Cash machine block delay [C.mach.blk.del.] – the time counted from the moment of

entering the user code of the CASH MACHINE ZONES BYPASSING type. After expiry of this time,

the 24H CASH MACHINE type zones will be bypassed.

Cash machine block time [C.mach.blk.time] – the time during which the 24H CASH MACHINE

type zones will be bypassed after entering the user code of the CASH MACHINE ZONES

BYPASSING

type. The bypass can be delayed by the CASH MACHINE BLOCK DELAY.

Disarm delay – the parameter applies to the BANK VAULT partition type. The partition will only

be disarmed after a defined period of time has elapsed since the code was used by the

user. If the time is equal to 0, the partition will be disarmed immediately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info