Bedienungsanleitung Satel Integra 64 Plus (Seite 20 von 35) (Englisch)

699074

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

18 Installer Manual SATEL

5.6.1 Connecting the INT-VG or INT-AV module or CA-64 SM expander

When connecting the INT-VG voice module, INT-AV audio alarm verification module or the

CA-64 SM voice synthesizer expander, the CLK and DTA wires only are to be connected to

the bus. Each of these devices is additionally provided with the PIN5 connector, which should

be inserted into the control panel onboard socket designated as SYNT1 or SYNT2.

Only one INT-VG module or CA-64 SM expander can be connected to the

INTEGRA 64 Plus control panel, because it allows not more than 16 voice messages

to be played back.

5.6.2 Addressing devices connected to the expander bus

Each device to be connected to the expander bus must have its own individual address from

the 0 to 31 range. The addresses of devices connected to the same bus must not repeat (the

control panel does not support devices having identical addresses). It is recommended that

consecutive addresses be assigned starting from 0. In most devices, the address is set by

means of DIP-switches.

If the device is connected to the second bus, its address in the system can be

determined by adding the number 32 to the address set in it.

The address affects numeration of zones and outputs in the system (see section

NUMERATION OF ZONES AND OUTPUTS IN THE SYSTEM p. 28).

5.7 Connecting the detectors

How the detector is connected to the zone must be suitable for the configuration chosen for

that zone. The zones on the control panel mainboard support the following configurations:

NC – the wiring type dedicated to connecting devices with the NC (normally closed) alarm

output. Opening the circuit will trigger an alarm.

NO – the wiring type dedicated to connecting devices with the NO (normally open) alarm

output. Closing the circuit will trigger an alarm.

EOL – this wiring type may be used to connect devices having the NC or NO alarm output.

Closing or opening the circuit will trigger an alarm.

2EOL/NC – the wiring type recommended to connect detectors having the NC alarm output

and a tamper output. The zone can recognize 3 states: normal, alarm and tamper.

2EOL/NO – the wiring type similar as 2EOL/NC, but for detectors with the NO alarm output.

Roller – the wiring type dedicated to connecting roller shutter detectors.

Vibration – the wiring type dedicated to connecting vibration detectors. The zone will also

accept connection of a detector with the NC alarm output (e.g. a vibration detector and

a magnetic contact can be connected in series).

Follow output – in case of this configuration the detector should not be connected. The zone

status depends only on that of the selected output (the output is not to be physically

connected to the zone).

Roller 2EOL – the wiring type similar as 2EOL/NC, but for the roller shutter detectors.

Vibration 2EOL – the wiring type similar as 2EOL/NC, but for the vibration detectors.

3EOL/NC – the wiring type recommended for connecting detectors with the NC alarm output,

tamper output and anti-masking output. The zone can recognize 4 states: normal,

alarm, tamper and masking of detector.

3EOL/NO – the wiring type similar as 3EOL/NC, but for the detectors with the NO alarm

output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Plus Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info