Bedienungsanleitung Satel Integra 64 Plus (Seite 86 von 102) (Englisch)

699074

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

84 Programming SATEL

• identifiers assigned to the alarm system,

• list of event codes (not applicable to Contact ID and SIA formats).

10.1 Reporting parameters and options

See also section “Telephone options” p. 68.

Shown in square brackets are the names used in keypads.

10.1.1 Options

Station 1 or Station 2 – the control panel will make an attempt to send the event code to

station 1 and, if unsuccessful, to station 2.

Station 1 only – the event codes are only sent to station 1.

Station 2 only – the event codes are only sent to station 2.

Station 1 and 2 – the event codes are sent to both stations. For most formats, it is possible

then to define which events will be sent to the given station (see: EVENTS ASSIGNMENT).

Dual path reporting – the option is available when the ETHM-1 Plus module with the

INT-GSM module attached to it is connected to the control panel. The control panel will

make an attempt to send the event code to station 1 and, if unsuccessful, to station 2.

The dual path reporting requires that the following settings be additionally

programmed:

− just one transmission path for Station 1: ETHM (Ethernet) [settings of the ETHM-1

Plus module with the INT-GSM module connected to it],

− priority transmission path for Station 2: GPRS SIM1 or GPRS SIM 2 [settings of the

ETHM-1 Plus module with the INT-GSM module connected to it],

− IP format for both stations: SIA-IP,

− supervision of the link between the control panel and the central station:

SUPERVISION INTERVAL parameter configured at least for the first monitoring station.

No module restart reports [No rest. mon.] – when this option is enabled and the Contact ID

or SIA format is used for reporting, no event codes referring to module restarts will be sent

to the monitoring station.

Advanced

Long kiss-off signal – with this option enabled, the control panel will accept a long kiss-off

(acknowledgment) signal for receiving events in case of Ademco Express and Contact ID

formats. Enable this option in the event of telephone reporting if the monitoring station

acknowledges receiving events in a non-standard way (the kiss-off signal is longer than

800 ms).

Longer waiting for initial handshake – with this option enabled, the control panel will wait

longer for handshake from the monitoring station in case of sending events in the Ademco

Express, Contact ID or SIA format. Enable this option in the event of telephone reporting, if

the monitoring station sends a non-standard initial handshake.

Identifier confirmation required – the option refers to the SIA format. If it is enabled, the

control panel waits for acknowledgement by the monitoring station of receiving the

identifier with which the data were sent. The option refers to the telephone reporting.

6-character identifier – the option refers to the SIA format. If it is enabled, events will be

sent with a 6-character identifier. It consists of 2 parts: 2-character prefix and 4-character

identifier.

Send event source name – the option refers to the SIA format. If it is enabled, the name of

event source (zone, user, etc.) will also be sent along with the event code.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Plus Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info