Bedienungsanleitung Satel Integra 64 (Seite 100 von 114) (Englisch)

699075

100

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

98 Programming SATEL

12.1.3 SIA-IP

If events are to be sent in the SIA-IP format, you must program additional parameters for

each monitoring station.

Send MAC address [MAC] – if this option is enabled, the MAC address of ETHM-1 /

ETHM-1 Plus module will be sent with event code.

Send timestamp [Timestamp] – if this option is enabled, the date and time will be sent with

event code (the monitoring station can change the date and time in the control panel).

Encrypt data [Coded] – if this option is enabled, the data to be sent will be encrypted, and

the date and time will be sent with event code (the monitoring station can change the date

and time in the control panel).

SIA-IP key – the key to encrypt data to be sent using the SIA-IP format.

hex – if the option is enabled, you can enter up to 32 hexadecimal characters as the SIA-IP

KEY

. If the option is disabled, you can enter up to 16 alphanumeric characters as the

SIA-IP KEY.

SIA-IP acct – a string of up to 16 hexadecimal characters, which is used to identify the

control panel for the purpose of reporting in SIA-IP format.

Supervision interval [SIA-IP test] – an additional transmission can be sent at specified

intervals to check communication with the monitoring station. You can program a number

of days, hours, minutes and seconds between the transmissions.

12.1.4 Identifiers assignment

Define the identifier with which events relating to individual partitions, zones, keypads and

expansion modules will be sent. If no identifier is assigned to the given element of the

system, it will be impossible to define codes for events relating to it.

12.1.5 Event codes

For the pulse and Ademco Express formats, it is necessary to program codes which will be

reported to the monitoring station if the defined events occur. The reported events are those

for which a code different from “00” has been programmed. 2 hexadecimal characters (digits

or letters from A to F) are to be programmed.

In case of the CONTACT ID (SELECTED) and SIA (SELECTED) formats, indicate the events

which are to be reported, entering for them any code different from “00” (a code

consistent with the format specification will be sent, not the entered one). The events

for which the “00” code has been programmed will not be reported.

12.1.6 Test transmissions

The test transmission may be sent:

• at a specified time. The test transmission code will be sent regularly at a defined time. The

number of days between transmissions and the time of sending transmission are

programmed.

• in specified time intervals. For each monitoring station, the number of days, hours and

minutes between transmission can be individually programmed. The test transmission

code will be sent:

– after a predefined period of time has elapsed since the last transmission, irrespective of

whether it was a test transmission, or the code of another event was sent (the NO SYNC.

TO LAST TRANSMISSION

option disabled),

– at predefined time intervals (the NO SYNC. TO LAST TRANSMISSION option enabled).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info