Bedienungsanleitung Satel Integra 64 (Seite 110 von 114) (Englisch)

699075

110

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

108 Programming SATEL

When programming the control commands, remember that:

− the command can include from 4 to 16 alphanumeric characters,

− the command may not contain diacritic characters and/or spaces,

− the commands must be different (the same command must not be used for

controlling two zones, two functions, etc.),

− the content of one command may not be used as a whole when programming the

content of another command. For example, with the “zone1” and “zone11” type

commands, the control panel will be unable to execute the latter one.

Zone violation [SMS -> z.viol.]

SMS – the control command that can be sent in the SMS message to the control panel

telephone number in order to violate a zone (the zone will be violated after the SMS

message is received by the control panel). You can define up to 32 such control

commands and assign one zone to each of them.

Zone – the alarm system zone which is to be violated after the control panel receives an

SMS message with the control command. The zone need not to exist physically, but the

wiring type programmed for it must be different from NO DETECTOR or FOLLOW OUTPUT.

Starting the function [SMS -> function]

SMS – the control command that can be sent in the SMS message to the control panel

telephone number in order to run a function (the function will be started after the SMS

message is received by the control panel). You can define up to 8 such control commands

and assign one function to each of them.

Function – the function which is to be started after the control panel receives an SMS

message with the control command. You can select one of the following functions:

– arming in chosen mode,

– disarming,

– clearing alarm,

– zone bypassing (inhibiting),

– zone unbypassing,

– activating MONO SWITCH type outputs,

– activating BI SWITCH type outputs,

– deactivating BI SWITCH type outputs,

– switching over BI SWITCH type outputs.

Partitions – for some functions (arming/disarming, alarm clearing) you must indicate the

partitions where the function will be executed.

Zones – for some functions (bypassing/unbypassing zones) you must indicate the zones to

which the function applies.

Outputs – for some functions (activating/deactivating outputs) you must indicate the outputs

which will be controlled by the function.

Name – you can enter an individual name for the function. The name will be included in the

content of SMS message, with confirmation that the function has been executed.

Checking the system status

SMS [SMS check state] – the control command that can be sent in the SMS message to the

control panel phone number to check the state (status) of partitions. Having received the

SMS message, the control panel will send in response an SMS message containing

information on the partition status.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info