699537
17
Zoom out
Zoom in
Vorherige Seite
1/47
Nächste Seite
SATEL PERFECTA LTE 15
Hide arm state indication after [125.Suppr.arm] – time counted from the moment of
partition arming, after which the LED on keypad indicating the partition armed status goes
off. If value 0 is programmed, the LED will be ON always when the partition is armed.
4.1.3 Arming
Prevent arming if not ready [Check if ready] – if this option is enabled, the control panel will
perform a check during arming for any problems that may prevent arming the system.
These include:
a zone with enabled P
RIORITY
option is violated in the partition,
– the 3. I
NSTANT
, 4. D
OUBLE KNOCK
, 5. 24
H
B
URGLARY
, 7. 24
H
P
ANIC
, 8. 24
H
P
ANIC SILENT
,
9. 24
M
EDICAL
or 10. 24
H
F
IRE
type zone is violated in the partition,
– the 3. I
NSTANT
, 4. D
OUBLE KNOCK
, 5. 24
H
B
URGLARY
, 7. 24
H
P
ANIC
, 8. 24
H
P
ANIC SILENT
,
9. 24
M
EDICAL
or 10. 24
H
F
IRE
type zone or a zone with enabled P
RIORITY
option is
bypassed in the partition,
there is a tamper in the partition,
there is a trouble in the system.
The control panel checks the conditions twice:
before starting the arming procedure – the control panel will not start the arming
procedure, if any problems occur (the keypad provides a forced arming option – see
U
SER MANUAL
),
after finishing the exit delay countdown – the system will not be armed (the arming
procedure will end in failure), if there are any problems, which did not occur before
starting the exit delay countdown.
If the option is enabled and a zone of the 0. E
NTRY
/E
XIT
, 1. E
NTRY
/E
XIT FINAL
or 2. I
NTERNAL
type is violated at the moment the exit delay countdown expires and the partition is armed,
a warning alarm will be triggered. If the partition is not armed after exit delay countdown
expires, the warning alarm will not be triggered.
Arm even if not ready after exit delay [Arm ExDly w.trbl] – if this option is enabled, the
control panel will not check conditions after finishing the exit delay countdown (it will only
check the conditions before starting the arming procedure). The option is available, when
the P
REVENT ARMING IF NOT READY
option is enabled.
Do not arm if battery trouble [BAT low = no arm] – if this option is enabled, forced arming
will be impossible in the event of battery trouble. The option is available, when the
P
REVENT ARMING IF NOT READY
option is enabled.
Do not arm if tampered [Tamper = no arm] – if this option is enabled, forced arming will be
impossible in the event of tamper. The option is available, when the P
REVENT ARMING IF NOT
READY
option is enabled.
4.1.4 Options
Service Mode beep [SM sounds] – if this option is enabled, the service mode will be audibly
signaled on the keypad.
Signal trouble state in partial arming [Trbl.in part.arm] – if this option is enabled, the
LED on the keypad goes off after both partitions are fully armed. If the option is disabled,
the LED goes off after just one of the partitions is armed in any mode.
Lock after three incorrect codes [3wrng.codes=blk.] – if the option is enabled, after
entering an incorrect code three times, the keypad will be blocked for 90 seconds. Entering
an invalid code again will prolong the locking.
Entering an invalid code three times may trigger alarm (cf. the keypad A
LARM
3
INCORRECT CODES
option).
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satel PERFECTA 32 LTE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satel PERFECTA 32 LTE

Satel PERFECTA 32 LTE Bedienungsanleitung - Deutsch - 11 seiten

Satel PERFECTA 32 LTE Zusatzinformation - Deutsch - 50 seiten

Satel PERFECTA 32 LTE Installationsanweisung - Deutsch - 27 seiten

Satel PERFECTA 32 LTE Kurzanleitung - Englisch - 10 seiten

Satel PERFECTA 32 LTE Bedienungsanleitung - Englisch - 30 seiten

Satel PERFECTA 32 LTE Zusatzinformation - Englisch - 50 seiten

Satel PERFECTA 32 LTE Installationsanweisung - Englisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info