Bedienungsanleitung Satel VERSA 10 (Seite 36 von 42) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

34 VERSA SATEL

Edit users – when the option is enabled, the person using the service code can add, edit and

remove users.

Arm/Dis/Clr/Bps – when the option is enabled, the person using the service code can arm

and disarm the system, clear alarms, and bypass zones (inhibit or isolate).

6.22.2 Defining the service access time

The function is available when the PERMANENT ACCESS option is disabled (see: “Defining the

service access rules”).

Enter the user menu and press in turn . The number of remaining hours

will be displayed, during which the access to the alarm system is still possible by using the

service code. Enter a new value from the range of 0 to 255 hours and press

6.22.3 Replacing batteries in wireless keypad

The function is available if a wireless keypad is installed in the alarm system. The function is

supported by ACU-120 / ACU-270 controller with firmware version 5.03.

1. Enter the user menu and press in turn

2. Keep pressing or until the name of the keypad in which you want to replace

the battery is displayed.

3. Press . The status of tamper switch in the keypad will not be checked for 3 minutes,

which allows you to replace the battery.

7. Operating the alarm system by means of keyfob

The alarm system can be operated by means of keyfobs, if the 433 MHz keyfobs receiver

expansion module (INT-RX-S / INT-RX), 433 MHz wireless system controller (VERSA-MCU)

or ABAX wireless system controller (ACU-120 / ACU-270 / ACU-100 / ACU-250) is

connected to the control panel.

The user can have two keyfobs:

 433 MHz keyfob – supported by the 433 MHz keyfobs receiver expansion module or 433

MHz wireless system controller,

 APT-100 bidirectional keyfob – supported by the ABAX wireless system controller.

A single keyfob enables up to 6 functions to be executed. The list of functions assigned to the

buttons / combination of buttons should be obtained from the person who configured the

keyfob settings when adding / editing a user. In the case of APT-100 keyfob, that person

should also provide information about functionality of the LEDs. The keyfob LEDs can be

used to confirm execution of functions, as well as to indicate the system status (pressing

a button on the APT-100 keyfob is accompanied by the LEDs flashing rapidly three times,

and in a little while the LED(s) may come on for 3 seconds to provide information).

The installer can configure the alarm system so that the sirens connected to the

system outputs can inform the user about the following events:

1 tone – starting the arming procedure (which is equivalent to arming, if the exit delay

has not been programmed),

2 tones – disarming,

4 tones – alarm clearing,

7 tones – arming is not possible, or the arming procedure has failed.

Tone duration is approx. 0.3 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info