Bedienungsanleitung Satel VERSA 10 (Seite 12 von 32) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

10 VERSA SATEL

3.5 Triggering the alarm from keypad

The installer can permit triggering alarms from the keypad. To trigger an alarm, do the

following:

fire alarm – press for approx. 3 seconds,

medical (auxiliary) alarm – press for approx. 3 seconds,

panic alarm – press for approx. 3 seconds. The installer defines whether the loud

panic alarm (setting off the loud alarm signal) or the silent panic alarm (without the loud

signal) will be triggered.

3.6 Turning the CHIME on /off

The CHIME is five short sounds by means of which the keypad will inform you e.g. that

a door / window is open, when the system is disarmed. The installer defines which zones of

the alarm system can trigger the CHIME and whether it can be turned on/off by the users.

Press and hold down for about 3 seconds to turn on or off the CHIME signaling.

3.7 User menu

Enter the code and press to get access to the user menu. Which functions you can

start depends on your rights, as well as status and configuration of the system.

In order to quit the function and/or user menu, press . The keypad will quit the menu

automatically, if 2 minutes have elapsed since the last keypress.

3.7.1 Running the functions

The functions are numbered. To run a function, enter the digit or a sequence of digits, and

then press . The sequences of keys which are to be pressed to run each function are

presented in section “User functions list” (p. 12).

For example, to start the zone inhibiting function, enter the user menu and then press

3.7.2 “Step by step” programming method

In case of some functions (e.g. adding and editing users, configuring timers, etc.), the

programming is effected by using the “step by step” method. After calling the function and

selecting the item to be configured from the list, the first parameter available for programming

will be displayed. After pressing , you will go on to programming another parameter (if

you have entered some changes, they will be saved). After all parameters have been

configured, you will either return to the selection list or exit the user menu, depending on the

function. The

and LEDs of the first and second partition show the number of

programming step (see: table 1). Some programming steps may be sometimes not available.

3.7.3 Entering data

The changes entered will be saved after pressing the key. Use the key to quit

the function without saving changes.

Entering digits

To enter digits, use the numeric keys. The digits are presented by means of LEDs (up to 6

digits). A single digit is presented on four LEDs – see Table 1. LEDs 1-4 present the first

digit, LEDs 5-8 – the second, LEDs 9-12 – the third, LEDs 16-19 – the fourth, LEDs 20-23 –

the fifth, and LEDs 24-27 – the sixth digit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info