Bedienungsanleitung Satel VERSA 10 (Seite 21 von 32) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

SATEL VERSA 19

13. Arming: Partition 1 LED is ON when partition 1 is armed

14. Arming: Partition 2 LED is ON when partition 2 is armed

15. Arming: Partition 1 or 2 LED is ON when partition 1 or 2 is armed

16. Arming: Partition 1 and 2 LED is ON when partitions 1 and 2 are armed

17. Partition 1 – Full arm LED is ON when partition 1 is armed in full mode

18. Partition 1 – Night arm LED is ON when partition 1 is armed in night mode

19. Partition 1 – Day arm LED is ON when partition 1 is armed in day mode

20. Partition 2 – Full arm LED is ON when partition 2 is armed in full mode

21. Partition 2 – Night arm LED is ON when partition 2 is armed in night mode

22. Partition 2 – Day arm LED is ON when partition 2 is armed in day mode

23. Partition 1 – Alarm LED is ON when there is alarm in partition 1

24. Partition 2 – Alarm LED is ON when there is alarm in partition 2

25. Partition 1 or 2 – Alarm LED is ON when there is alarm in partition 1 or 2

26. Trouble LED is ON when there is trouble in the system

27. Partition 1 – Not armed LED is ON when partition 1 is disarmed

28. Partition 2 – Not armed LED is ON when partition 2 is disarmed

29. Partition 1+2 – Not armed LED is ON when partitions 1 and 2 are disarmed

255. NOT PRESENT LED will not be used for confirmation

Contact the installer to obtain information on the zone types and output functions.

24. Step 6j. Selecting confirmation for LED 2 in APT-100 keyfob. Proceed in the same

way as in Step 6i.

25. Step 6k. Selecting confirmation for LED 3 in APT-100 keyfob. Proceed in the same

way as in Step 6i.

Pressing the key between Step 6a and 6k will cancel the keyfob adding, but will

not terminate the user adding procedure.

26. Step 7. Adding proximity card. If a device provided with proximity card reader is

installed in the system, a proximity card can be assigned to the user. Press in turn

and

(if a proximity card is to be assigned to the user) or only (if no proximity

card is to be assigned to the user).

27. Step 7a. Selecting card addition method. Press

(if the card code is to be

entered) or select the device, by means of which the card code will be read. The LEDs

corresponding to the addresses of devices are steady on, and the and keys

allow you to select the device (the LED corresponding to the selected module will start

blinking). Having selected the device, press .

28. Step 7b. Adding proximity card. Depending on the selected method:

– enter the card code (see: “Entering hexadecimal characters” p. 11) and press ,

– bring the card twice close to the reader (displayed messages will prompt you what to

do). Remember that the card number will only be sent by the proximity card

arm/disarm device after the card is moved away from the reader.

Pressing the key in Step 7a or 7b will cancel the card adding.

3.9.2 User editing

1. Enter the user menu and press in turn . User editing is effected by the

“step by step” method, hence the programming step number is presented on the and

LEDs of the first and second partitions (see: page 11, Table 1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info