Bedienungsanleitung Satel VERSA 10 (Seite 39 von 87) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

SATEL VERSA 37

In case of the VIBRATION zone wiring, opening the circuit for 200 ms or longer –

irrespective of the programmed number of pulses and sensitivity (see below) – will be

interpreted as violation. This solution enables a magnetic contact to be connected in

series with the vibration detector.

Sensitivity – depending on selected wiring type:

– NO, NC, EOL and 2EOL – the time during which the zone must be violated, so that it

can be noted by the control panel. The sensitivity is programmed in milliseconds.

Values from the 20 ms to 5100 ms range can be entered.

– Vibration – the pulse whose duration is equal to or longer than the defined time will

cause violation of the zone. Values from the 3 ms to 96 ms range can be programmed

(every 3 ms).

Pulse validity – the time counted from the pulse occurrence during which subsequent pulses

must occur (their number being defined as the PULSE COUNT) so that the zone is violated.

The following values can be programmed: 30 s, 120 s, 240 s and 0. If no further pulses will

occur within the defined time period, the pulse counter will be reset. The pulse counter is

reset automatically at arming/disarming. If the value 0 is programmed, the counter will only

be reset at arming/disarming. This parameter is programmed for the ROLLER zone wiring.

Pulse count – the number of pulses after which the zone will be violated. This parameter is

programmed for the ROLLER and VIBRATION zone wiring. For the VIBRATION zone wiring, it is

possible to program values from 0 to 7 (for the value 0, the pulses will not be counted, the

SENSITIVITY parameter only being taken into account). For the ROLLER zone wiring, you can

program values from 1 to 8.

In the DLOADX program, all the required parameters for zones in ROLLER and

VIBRATION configuration are programmed in the “Sensitivity” field.

Max. violation time – if the zone is violated for the preset time (e.g. because the detector is

damaged or masked), a trouble will be reported. Up to 255 seconds can be programmed.

Programming the value 0 means that the control panel will not check whether the zone is

violated too long.

Max. no violation time – if zone is not violated for the preset time (e.g. because of

damaging or masking the detector), a trouble will be reported. When the zone is armed,

the countdown is not running. You can program up to 255 hours. Programming the value

0 means that the control panel will not check whether the zone is violated or not.

6.4 Zone types

0. ENTRY/EXIT – a delayed zone combining two functions:

entry – violation of the zone starts entry delay counting in the partition and turns on delay

for the 2. E

NTRY/EXIT ROUTE type zone.

exit – violation of the zone during exit delay countdown is equivalent to the partition exit.

1. ENTRY/EXIT FINAL – the same as the 0. ENTRY/EXIT type, but if the arming procedure has

started and the control panel registers the zone restore, the exit delay countdown will be

terminated.

2. ENTRY/EXIT ROUTE – during the countdown of ENTRY DELAY or DELAY ACTIVATION TIME the

zone acts as a delayed one (alarm will be triggered after expiry of the DELAY TIME). In other

situations it acts as an instant zone.

3. INSTANT – instant zone, which is already armed during exit delay countdown.

4. DOUBLE KNOCK – the zone triggers the burglary alarm only after the second violation. The first

violation of the zone only results in the “Zone violation” event being logged (the event to may

reported in format 4/2). The second violation must take place during the WAITING TIME

countdown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info