Bedienungsanleitung Satel VERSA 15 (Seite 10 von 11) (Englisch)

699458

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

8 VERSA SATEL

The user can have two keyfobs:

 433 MHz keyfob – supported by the 433 MHz keyfobs receiver expansion module or 433

MHz wireless system controller,

 APT-100 bidirectional keyfob – supported by the ABAX wireless system controller.

A single keyfob enables up to 6 functions to be executed. The list of functions assigned to the

buttons / combination of buttons should be obtained from the person who configured the

keyfob settings when adding / editing a user. In the case of APT-100 keyfob, that person

should also provide information about functionality of the LEDs. The keyfob LEDs can be

used to confirm execution of functions, as well as to indicate the system status (pressing

a button on the APT-100 keyfob is accompanied by the LEDs flashing rapidly three times,

and in a little while the LED(s) may come on for 3 seconds to provide information).

3. Operating the alarm system by telephone

If the INT-VG voice module is connected to the control panel, you can operate the alarm

system by using a touch-tone (DTMF) telephone. The voice menu makes the operation an

easy job. To access the voice menu, call the phone number of the control panel.

3.1 Starting the operating by telephone

1. Call the control panel phone number. After the call is received, you will hear three short

beeps.

The installer can configure the control panel in such a manner that the telephone

communicator will only go off hook after the recall. If this is the case, call the number,

but hang up after the number of rings which has been set by the installer. Call again

within three minutes. The call will be received.

2. Enter the code from the telephone keypad and confirm by pressing #. 4 short beeps

followed by 1 long beep will confirm you have got access to the interactive voice menu. If

your code does not authorize you to get access, you will hear three long beeps in the

headset. If the code is incorrect, you will hear two long beeps in the headset.

3. Messages of the interactive voice menu will be played back. They will inform you which

telephone keys you should use to be able to operate the control panel.

3.2 Ending the operating by telephone

1. Press

key.

2. Press in turn the 0# keys. The control panel will go on-hook.

The control panel will goes on hook automatically after one minute of idle state.

4. VERSA CONTROL application – first steps

If the ETHM-1 Plus module is connected to the control panel, you can operate the alarm

system from mobile devices using VERSA CONTROL application. Additionally, the

application can provide information about alarm system events by using push notifications.

You can download the application from the internet stores: “Google play” (Android system

devices) or “App Store” (iOS system devices).

Having installed the application:

 enter the name of control panel (to enable identification of the control panel when using

the application),

 enter the MAC address of ETHM-1 Plus module,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 15 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info