Bedienungsanleitung Satel VERSA 5 (Seite 15 von 42) (Englisch)

699460

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

SATEL VERSA 13

“Bypassed zones 1=Arm” – if you don’t have the ZONE INHIBITION right. You can:

– press the key to cancel the arming,

– press the key to proceed with the arming.

6.3.7 Denial of arming and forced arming

The installer can configure the control panel so that initiating the arming procedure is

impossible, if:

 in the partition to be armed, at least one zone that must not be violated during arming (the

PRIORITY option has been enabled for the zone by the installer) is violated,

 in the partition to be armed, at least one alarm zone is violated beyond the exit route,

 there is trouble in the system.

If you have the INSPECTION right, you will be informed about the cause of refusal to arm the

system (the order of message descriptions corresponds to their priority):

“Zone [zone number] violat.” – a zone with enabled PRIORITY option is violated. If two or

more such zones are violated, the indicator will be flashing on the display. To scroll

through the list of violated zones, use the and keys. You can:

– press the key to cancel the arming,

– press the key to inhibit the violated zone (you must have the ZONE INHIBITION

right). A message will be displayed, prompting you to confirm the command to inhibit the

zone (press to inhibit the zone, or to cancel inhibiting the zone).

The system can be armed after eliminating the cause of the zone violation, or after

bypassing the zone.

“Violated zones 1=Ok 2=Check” – an alarm zone outside of the exit route is violated. You

can:

– press the key to cancel the arming,

– press the key to force the arming,

– press the key to check which zone is violated. If two or more such zones are

violated, the indicator will be flashing on the display. To scroll through the list of

violated zones, use the

and keys. If you have the ZONE INHIBITION

permission, you will be able inhibit the violated zone by pressing . A message will

be displayed, prompting you to confirm the command to inhibit the zone (press to

inhibit the zone, or to cancel inhibiting the zone).

“Troubles 1=Ok 2=Check” – there is a trouble in the system. You can:

– press the key to cancel the arming,

– press the key to force the arming,

– press the key to view the trouble log – the 7. SYSTEM STATE function will start

(see: “Checking the troubles / system state” p. 30).

Information on the forced arming is written into the event log.

6.3.8 Failure of arming procedure

The installer can configure the alarm system in such a manner that it will not be armed, if at

the moment of completing the exit delay countdown:

 there is a violated zone in partition which was not violated when the arming procedure was

started,

 there is a trouble which did not exist when the arming procedure was started.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 5 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info