Bedienungsanleitung Satel VERSA 5 (Seite 25 von 36) (Englisch)

699460

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SATEL VERSA 23

Do not connect deeply discharged battery to the control panel (with voltage

across unloaded terminals below 11 V). The battery should be precharged with

a proper charger.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

5.10.3 Control panel power-up / start-up procedure

1. De-energize the 230 V AC circuit to which the transformer is to be connected.

2. Connect the 230 V AC wires to the terminals of transformer primary winding.

3. Connect the terminals of transformer secondary winding to the control panel AC

terminals. To make the connection, use flexible conductors with a cross-section of 0.5 –

0.75 mm

, or rigid conductors with a cross-section of 1 – 2.5 mm

4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative

terminal to BLACK lead). If the battery has screw-type cable lugs, use adapters delivered

with the control panel (do not cut off the battery cable lugs). The control panel will not

start after connecting the battery alone.

5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.

The control panel will start operating.

The above mentioned power-up sequence (first the battery, then the 230 V AC mains)

will ensure proper operation of the power supply unit and the electronic protection

circuits, thus preventing damage to the alarm system components caused by

installation mistakes, if any.

If it is necessary to de-energize the control panel, turn off the main power supply (AC)

first, and the backup power supply (battery) afterwards. Observe the above described

procedure when reconnecting the power supply.

5.10.4 Emergency procedure of the control panel start-up

If the control panel fails to start properly, keypads are not supported, codes are not accepted

by the control panel etc., despite all connections having been made correctly, follow the steps

below:

1. Turn off the control panel power supply (first disconnect the AC power, and then the

battery).

2. Put a jumper on the RESET pins.

3. Turn on the control panel power supply (first connect the battery and then the AC power).

4. Wait a few seconds and remove the jumper from the RESET pins. The control panel will

enter the service mode. The service mode menu will be displayed on the keypad with the

lowest address (in the case of a wireless keypad, the menu will be displayed on pressing

any key).

If the SERVICE MODE FROM RESET PINS option is disabled in the control panel then,

depending on the type of keypad in which the lowest address is set:

 LCD: the , and (of the second partition) LEDs will be lit, and the

message “Restore factory settings ? 1=Yes” will come up on the display,

 LED: the and (of the second partition) LEDs will be lit and the

LED will

be blinking rapidly.

Pressing the key will reset the control panel to its factory settings, but will enable

entering the service mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 5 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info