Bedienungsanleitung Satel VERSA 5 (Seite 30 von 36) (Englisch)

699460

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

28 VERSA SATEL

8. Click on the “Write” button to write the new wireless device data to the controller (these

data will not be written after clicking on the button in the main menu).

LCD keypad

You can add ABAX wireless devices in the service mode by means of the NEW DEVICE

function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD. 1. NEW

DEVICE

1. Having started the function, enter the 7-digit serial number of the added device and press

the key. The serial number can be found on the electronics board or on the

enclosure. Each ARF-100 radio signal level tester has serial number 0000500.

2. When the “Open device tamper” message is displayed, depending on the device type:

ACX-200 / ACX-201: power-up the expander,

ARF-100: turn on the device,

ASW-100 E / ASW-100 F: insert the controller into 230 V AC socket,

other devices: open the tamper contact.

3. Information on the device to be added will be displayed (if nothing happens, it can mean

that you have entered an invalid serial number – if this is the case, press to return

to the submenu). Press to confirm your intention to add a device.

4. Using the and keys, select the zone to which the device is to be assigned

and then press .

5. The new name of the zone will be displayed. You can change it. The same name will also

be given to the output, if the device is assigned to the output. Press to save the

name. If the device takes up several positions, the name-giving procedure must be

repeated for them.

6. In the next steps, you can configure the device (see the PROGRAMMING manual).

5.14.2 Removing ABAX wireless devices

DLOADX program

You can remove ABAX wireless devices in the “VERSA – Structure” window, “Hardware” tab,

after clicking on the ABAX system controller name in the list of devices.

1. In the “Zones/Outputs” tab, click on the “Read” button to read the data related to wireless

devices from the controller.

2. Click on the zone to which the device you want to delete is assigned (if the device is

assigned to several zones, you can click on any of them).

3. Click on the “Delete”

button. The “Confirm” window will open.

4. Click on the “Yes” button. The “Confirm” window will close.

5. Click on the “Write” button to save the changes to the controller.

LCD keypad

You can remove ABAX wireless devices in the service mode by means of the REMOVE DEVICE

function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD. 3. REMOVE

DEVICE

1. Having started the function, use the

and keys to select the zone to which the

wireless device to be removed is assigned, and then press .

2. A prompt will appear asking you whether the device is to be deleted (device type and

serial number will be displayed). Press . The device will be deleted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 5 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info