Bedienungsanleitung Satel Versa IP (Seite 73 von 93) (Englisch)

629722

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

SATEL VERSA IP 71

 identifier 2 – alarms triggered from keypad, arming/disarming by means of zones, quick

arming, loss of communication with wireless devices, as well as expander troubles

and tampers,

 identifier 3 – arming/disarming and alarm clearing by means of code or proximity card,

 system identifier – power supply troubles, zone bypasses, troubles of control panel high-

current outputs, communication bus trouble, programming related events, etc.

The identifier consists of 4 hexadecimal characters (digits or letters from A to F). Entering the

value 0000 means that events assigned to that identifier will not be reported. Using the digit 0

in the identifiers is not recommended.

SIA / TELIM prefix – 2 characters which will precede each of the identifiers in case of the

SIA and TELIM formats. Thus an identifier consisting of 6 characters can be obtained. 2

hexadecimal characters (digits or letters from A to F) can be programmed. Entering 00

means that the prefix will not be added. Using the digit 0 in the prefix is not recommended.

Station 1 options / Station 2 options

SIA – send part. name – if the option is enabled, in the SIA format, the name of partition

where the event took place will also be sent, in addition to the event code.

SIA – send source name – if the option is enabled, in the SIA format, the name of event

source (zone, user, etc.) will also be sent, in addition to the event code.

SIA – confirm each block – if the option is enabled, the control panel will wait for

acknowledgement by the monitoring station of receiving every data block sent in the SIA

format. The option applies to telephone reporting.

SIA – id. conf. required – if the option is enabled, the control panel will wait for

acknowledgement by the monitoring station of receiving the identifier with which the data

were sent. The option applies to telephone reporting.

Longer waiting for initial handshake – if the option is enabled, the control panel will wait

longer for handshake from the monitoring station in case of sending events in the Ademco

Express, Contact ID or SIA format. Enable this option in the event of telephone reporting, if

the monitoring station sends a non-standard initial handshake.

Long kiss-off signal – if the option is enabled, the control panel will accept a long kiss-off

(acknowledgment) signal for receiving events in case of Ademco Express and Contact ID

formats. Enable this option in the event of telephone reporting, if the monitoring station

acknowledges receiving events in a non-standard way (the kiss-off signal is longer than

800 ms).

11.2.3 Test transmissions

The test transmission is sent through all transmission paths which are shown on the

list defining the order in which transmission paths are used (see: “Transmission

priority” p. 72).

The test transmission may be sent:

 at a specified time. The test transmission code will be sent regularly at a defined time. The

number of days between transmissions and the time of sending transmission are

programmed. Programming the value 0 for days means that the transmission will be sent

everyday (in the same way, as in case programming the value 1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa IP Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa IP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info