Bedienungsanleitung Satel Versa IP (Seite 24 von 43) (Englisch)

629722

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

22 VERSA IP SATEL

10. Step 5e. Assigning function to 433 MHz keyfob button 3. Proceed in the same way as

in Step 5c.

11. Step 5f. Assigning function to 433 MHz keyfob button 4. Proceed in the same way as

in Step 5c.

12. Step 5g. Assigning function to 433 MHz keyfob button 5 (two buttons pressed

simultaneously – see: “Operating the alarm system by means of keyfob” p. 34). Proceed

in the same way as in Step 5c.

13. Step 5h. Assigning function to 433 MHz keyfob button 6 (two buttons pressed

simultaneously – see: “Operating the alarm system by means of keyfob” p. 34). Proceed

in the same way as in Step 5c.

Pressing the key between Step 5a and Step 5h will cancel the keyfob adding,

but will not terminate the user adding procedure.

14. Step 6. Adding APT-100 keyfob. If the ABAX wireless system controller is connected to

the control panel, the bidirectional APT-100 keyfob can be assigned to the user. Press in

turn and (if a keyfob is to be assigned to the user) or only (if no keyfob

is to be assigned to the user).

15. Step 6a. Selecting APT-100 keyfob addition method. Press (if the keyfob serial

number is to be entered) or press in turn (if the serial number is to be read by

the ABAX wireless system controller during transmission).

16. Step 6b. Adding APT-100 keyfob. Depending on the selected method:

– enter the keyfob serial number and press ,

– press twice any button on the keyfob (displayed messages will prompt you what to do).

Numbering of the buttons and LEDs on the APT-100 keyfobs is described in section

“Operating the alarm system by means of keyfob” (p. 34).

17. Step 6c. Assigning function to APT-100 keyfob button 1. Proceed in the same way as

in Step 5c.

18. Step 6d. Assigning function to APT-100 keyfob button 2. Proceed in the same way as

in Step 5c.

19. Step 6e. Assigning function to APT-100 keyfob button 3. Proceed in the same way as

in Step 5c.

20. Step 6f. Assigning function to APT-100 keyfob button 4. Proceed in the same way as

in Step 5c.

21. Step 6g. Assigning function to APT-100 keyfob button 5. Proceed in the same way as

in Step 5c.

22. Step 6h. Assigning function to APT-100 keyfob button 6 (two buttons pressed

simultaneously: 1 and 5). Proceed in the same way as in Step 5c.

23. Step 6i. Selecting confirmation for LED 1 in APT-100 keyfob. Press to confirm

the default method of confirmation (defined by the installer in the user schedule) or enter

the number of one of the following functions and then press :

0. On LED is ON, when the control panel has acknowledged receiving

information on pressing a button

1. Output 1 state LED is ON, when the selected output is active

2. Output 2 state

3. Output 3 state

4. Output 4 state

5. Output 5 state

6. Output 6 state

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa IP Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa IP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info