Bedienungsanleitung Satel Versa IP (Seite 34 von 43) (Englisch)

629722

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

32 VERSA IP SATEL

When testing the zones, the keypad does not present the current zone state, but only

indicates whether or not the zone was violated during the test.

1. Enter the user menu and press in turn .

2. Enter two digits to define the test duration (e.g. if the time is to be 5 minutes, press in turn

and – the test may last from 1 to 15 minutes), and then press . The

keypad will indicate the zones which can be tested, using the symbol (the numbers

around the display enable identification of the zones).

3. Violate the selected zones (e.g. walking through the area supervised by the motion

detector or opening the window supervised by the magnetic contact). The keypad should

inform you that the zone has been violated (the zone symbol changes to ). Information

on the violation will be presented until the zone test is terminated.

4. The test will be terminated automatically after the defined time has elapsed. You can

terminate it earlier by pressing .

6.21.2 Output test

The function makes it possible to check proper functioning of the system outputs as well as

devices connected to them.

You can always test 12 outputs.

1. Enter the user menu and press in turn

. The keypad will present the

state of outputs in the upper line of the display (

– output inactive; – output active).

The name of output over which the cursor is currently situated is displayed in the lower

line. The and keys allow moving the cursor.

2. Press to activate the output, or to deactivate the output.

3. Press to quit the function.

6.21.3 Checking the level / quality of radio signal

The function allows you to check:

 the quality of radio signal received by the controller from 433 MHz wireless detectors (if the

VERSA-MCU controller is connected to the control panel),

 the level of radio signal received by the controller from ABAX wireless devices (if the

ABAX system controller is connected to the control panel).

Enter the user menu and press in turn

. In the lower line of the display, the

information on signal level / quality will be shown. The upper line displays the name of zone

to which the wireless device is assigned.

Use the arrow keys to scroll through the list.

6.21.4 Starting the manual test transmission

Enter the user menu and press in turn . A “Manual reporting test” event will

be saved to the control panel memory. The event code will be sent to the monitoring station.

6.21.5 Telephone reporting test

Enter the user menu and press in turn (test of telephone reporting to

Station 1) or (test of telephone reporting to Station 2). Messages with

information on the currently realized operations will appear on the display. This allows

problems, if any, to be diagnosed.

6.21.6 Checking the firmware version of control panel

Enter the user menu and press in turn . Information on the control panel

firmware version and build date will be displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa IP Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa IP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info