Bedienungsanleitung Satel VERSA-KWRL2 (Seite 6 von 14) (Englisch)

699461

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

4 VERSA-KWRL2 SATEL

2. Install the batteries and add the keypad to the wireless system (see “Adding the keypad to

the wireless system”).

3. Put the cover on the catches and snap the enclosure shut.

4. Place the keypad in the location intended for its installation.

If you want to hold the keypad in your hand when checking the radio signal level, grab

the device from its left side (on its right side, there is the antenna, which must not be

covered).

5. Check the level of signal received from the keypad by the ABAX 2 / ABAX controller. If the

signal level is lower than 40%, select another place for installation. Sometimes, it is

sufficient to shift the device ten or twenty centimeters to obtain a considerable

improvement in the signal quality. Only after the optimal level of radio signal is achieved

can you proceed to the next step.

The ARF-200 tester makes it possible to check the radio signal strength at the place of

future installation without having to put the keypad there.

6. Open the keypad enclosure (Fig. 2).

7. Place the enclosure base against the wall and mark location of the mounting holes.

8. Drill the holes in the wall for wall plugs (anchors).

9. Using wall plugs (anchors) and screws, secure the enclosure base to the wall. Select wall

plugs specifically intended for the mounting surface (different for concrete or brick wall,

different for plaster wall, etc.). When installed, the device must withstand a pull-off force of

at least 50 N.

10. Put the cover on the catches and snap the enclosure shut.

11. Lock the cover using screw.

3.1 Adding the keypad to the wireless system

Before adding the keypad, make sure that the CKE and DTE terminals of the

controller are connected to the control panel communication bus. Also,

depending on the controller:

 ACU-220 / ACU-280: check that the switch 9 is set in OFF position, and switch

10 is set in ON position,

 ACU-120 / ACU-270: check that the switch 8 is set in ON position.

You can add the wireless keypad to the ABAX 2 / ABAX system by using either a c

omputer

with DLOADX program installed, or an LCD keypad. The controller allows for registering of

up to 6 VERSA-KWRL2 keypads. If no wired keypad is connected to the control panel, you

can only add the first wireless keypad using the DLOADX program (to establish

communication between the program and the control panel, you must start the service mode

“from pins” – refer to the control panel programming manual).

When adding the device, its serial number is required. The serial number sticker can be

found on the electronics board.

The keypad is identified as LCD-WRL.

Simultaneous operation of the keypad by

the ABAX 2 and ABAX controller is not

possible.

3.1.1 DLOADX program

You can add wireless keypads in the “VERSA – Structure” window, “Hardware” tab, after

clicking on the name of ABAX 2 / ABAX controller on the list of devices, and then on the

“LCD-WRL” tab (see: Fig. 3 p. 7).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA-KWRL2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA-KWRL2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info