Bedienungsanleitung Satel VERSA-LCDM-WRL (Seite 4 von 12) (Englisch)

699462

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

2 VERSA-LCDM-WRL SATEL

2. Description

Operating modes

The keypad can work in two modes:

active mode – started by pressing any key. Additionally, the active mode can be started automatically

when an alarm occurs or an entry delay, an exit delay or an auto-arming delay begins (see

description of the

AKE

parameter, section “Settings stored in ABAX system controller” p. 5).

In this mode, the keypad operates in much the same way as the LCD wired keypad. The display is

ON and the backlight, LED signaling and sound signaling are active.

inactive mode – is started:

– after 20 seconds since the last key press,

– after preset time, if the active mode was started automatically (see description of the

AKE

parameter, section “Settings stored in ABAX system controller” p. 5).

The purpose of the

inactive mode is to save energy. The display is off. Backlight, LED indication

and sound signaling are disabled (if a time different from 0 is preset for the

AKE

parameter,

CHIME from zones will be signaled).

Support for proximity cards

The built-in

proximity card reader enables the system to be operated by using proximity cards (any

125 kHz passive transponder in the form of a card, tag, etc.). If the alarm system is not to be operated

by using the proximity cards, the reader can be disabled (thus reducing the battery consumption).

Periodic transmissions

Every 15 minutes, the

keypad sends a periodic transmission. The purpose of such transmissions is to

monitor presence and condition of the keypad.

Battery status control

The keypad controls the

status of the batteries. If the voltage is lower than 2.75 V:

 low battery information is sent during each periodic transmission,

 on entering the active mode, a low battery message will be displayed (the message will specify

which battery is to be replaced – the battery designation can be found on the electronics board,

after opening the enclosure).

The battery life depends on how the keypad is used. The more frequently the active mode is

entered, the quicker the batteries will be depleted.

3. Installation

There is a danger of battery explosion when using a different battery than

recommended by the manufacturer, or handling the battery improperly.

Be particularly careful during installation and replacement of the batteries. The

manufacturer is not liable for the consequences of incorrect installation of the battery.

The used batteries must not be discarded, but should be disposed of in accordance

with the existing rules for environment protection.

The keypad is designed for indoor installation. The place of installation should be readily accessible to

the system users. When selecting the installation location, take into account the communication range

of the ABAX system.

1. Open the keypad enclosure (Fig. 2).

. Install the batteries and add the keypad to the wireless system (see: “Adding the keypad to the

wireless sy

stem”).

Put the cover on the catches and snap the enclosure shut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA-LCDM-WRL Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA-LCDM-WRL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info