Bedienungsanleitung Satel VERSA-MCU (Seite 2 von 4) (Englisch)

699463

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

2 VERSA-MCU SATEL

3. Installation

Disconnect power before making any electrical connections.

The controller should be installed indoors, in spaces with normal air

humidity. When selecting the installation place, remember that the thick

walls, metal partitions, etc. will reduce the range of the radio signal. It is

recommended that the controller be mounted high above the floor. This

will allow you to get a better range of radio communication and avoid

the risk of the controller being accidentally covered by people moving

around the premises. Mounting the controller near electrical installations

is not advisable, as this may cause malfunction of the device.

1. Open the enclosure of the controller (Fig. 2).

2. Make the opening in the enclosure base for the communication bus

and power cables.

3. Pass the cables through the opening. It is recommended to use

a straight-through unshielded cable. When using the twisted-pair

type of cable, the CLK (clock) and DAT (data) signals must not be

sent through one twisted pair.

4. Using wall plugs (screw anchors) and screws, fasten the enclosure

base to the mounting surface.

5. Connect the CLK, DAT and COM terminals with wires to the

communication bus of VERSA control panel.

6. Connect the power leads to the +12 V and COM terminals. If the

distance to the control panel is less than 300 meters, the controller

can be supplied directly from the control panel. If the distance to the

control panel is higher, the controller must be supplied from another

power source, which is located at a closer distance (a power supply

unit or an expander with power supply).

7. Close the controller enclosure.

8. Turn on the power of the alarm system.

9. Start the identification function in the control panel. The controller

will be identified as two devices: INT-RX (address 7) and

VERSA-MCU (address 8).

3.1 Keyfobs

The data relating to keyfobs are stored in the controller. After a controller containing keyfob

data is connected to the control panel, keyfobs will be automatically assigned to the existing

users.

See the VERSA control panel manuals for information on the functions that can be run with

the keyfobs. After adding a keyfob, the functions provided for by the user schedule will be

automatically assigned to the buttons. The assigned functions may be replaced with other

ones.

The user manual for VERSA control panels describes the procedures for adding and editing

the user by means of the keypad, during which you can add or remove the keyfob and

determine what functions will be available from the keyfob.

Adding a 433 MHz keyfob by means of the DLOADX program

Adding a keyfob is possible in the "Versa – Structure" window, "Hardware" tab, after clicking

on the INT-RX in the list of devices. Before making any changes, click on the "Read" button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA-MCU Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA-MCU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info