Bedienungsanleitung Satel Versa Plus (Seite 67 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

SATEL VERSA Plus 65

The test mode is started/ended during polling, which results in a delay, its duration

depending on the programmed response period. The test mode will be turned off

automatically after 30 minutes of:

– starting the test mode from the DLOADX program (the 30-minute period is running from

the moment of exiting the controller settings),

– exiting the service mode in the control panel.

According to requirements of the EN50131 standard, the level of radio signals sent by

wireless devices is reduced during the test mode operation.

For the AMD-103 detector, entering the test mode remotely is not possible.

9.4.2 Parameters and options of ABAX system wireless devices

The wireless keypads constitute a special category of wireless devices for which a

separate group of positions is reserved in the controller. For information on configuring

the wireless keypads, refer to the manuals delivered with respective keypads.

Filter – the number of consecutive response periods, during which communication with the

device failed to be established, for the loss of communication with the device to be

reported. Values from the 0 to 50 range can be entered. Entering the digit 0 will disable

control of the device presence in the system.

In the case of the AMD-103 magnetic contact and ASP-100 siren, the presence check

is performed in a different way than for the other ABAX system devices. If the value

programmed for the FILTER parameter differs from 0, the lack of presence will be

reported if no transmission from the AMD-103 magnetic contact / ASP-100 siren is

received within one hour.

Always active [Active mode] – the option is available for the most of wireless detectors. If

enabled, the detector is permanently switched over to the active mode (see “ABAX

wireless detectors” p. 71).

The AMD-103 detector and the wireless detectors assigned to 24-h zones are always

in the active mode, therefore the ALWAYS ACTIVE option does not have to be enabled

for them.

Configuration – some of the wireless devices provide additional parameters and options,

which can be configured by radio (shown in square brackets is information on the zone for

which additional parameters can be programmed, if the device takes up more than 1

zone):

AGD-100 – wireless glass-break detector. Sensitivity is to be programmed.

AMD-100 / AMD-101 – wireless magnetic contact. The active reed switch is to be

selected.

AMD-102 – wireless magnetic contact with input for roller shutter detector. The following is

to be programmed:

 active reed switch [first zone],

 number of pulses after which alarm will be triggered by the roller shutter input

[second zone]

 time during which the specified number of pulses must occur for the roller shutter

input to trigger alarm [second zone].

AOCD-250 – wireless outdoor dual technology curtain detector. The following is to be

programmed:

 sensitivity of PIR sensor;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info