Bedienungsanleitung Satel Versa Plus (Seite 82 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

80 VERSA Plus SATEL

 supervision of the link between the control panel and the central station:

SUPERVISION INTERVAL parameter configured at least for the first monitoring station.

Events amount limiting – if the option is enabled, events from the same source are saved

into the event log and reported to the monitoring station 3 times only. This option does not

apply to the alarms from zones (see: AUTO-RESET 3 or AUTO-RESET 1 zone option).

Report module restarts – if the option is enabled, in case of sending event codes in Contact

ID or SIA format, the monitoring station is informed about module restarts.

Restore after bell – if the option is enabled, the zone restore code will only be sent to the

monitoring station after the alarm signaling ends. If a few outputs are signaling alarm, the

zone restore code will be sent when one of them stops signaling the alarm.

Restore after disarm – if the option is enabled, the zone restore code will only be sent to the

monitoring station after disarming the partition to which the zone belongs.

11.2.2 Station 1 / Station 2

Reporting format – format in which event codes are sent to the monitoring station.

In the TELIM format, events can only be sent via the analog telephone line.

Telephone

Telephone no. – telephone number of the monitoring station for reporting via the analog

telephone line.

Repetitions – the number of attempts to send an event code via the analog telephone line. If

all attempts fail, the control panel will suspend reporting via the analog telephone line. Up

to 31 retries can be programmed. Programming the value 0 means that monitoring will

be suspended after 8 attempts.

Suspend time – the time for which reporting will be suspended, if attempts fail to send an

event code through all provided transmission paths. The control panel will resume the

attempt of establishing telephone connection with the monitoring station after this time

expires or a next, new event occurs. Up to 30 minutes can be programmed. Programming

the value 0 means that an attempt to establish telephone connection with the monitoring

station will only be taken after occurrence of a new event in the system.

ETHM/GPRS

Server address – network address of the monitoring station for reporting via Ethernet or

GPRS. You can enter either the IP address or the domain name.

Port – number of port used for communication between the control panel and the monitoring

station. You can enter a value from 1 to 65535.

Station key – a string of up to 12 alphanumeric characters (digits, letters and special

characters), which is used for encryption of data sent to the monitoring station.

ETHM/GPRS key – a string of up to 5 alphanumeric characters to be used for identification of

the control panel for the purposes of reporting via Ethernet or GPRS.

Identifiers

Event codes are sent to the monitoring station with one of the four identifiers:

 identifier 1 – events from zones (alarms, tampers, troubles),

 identifier 2 – alarms triggered from keypad, arming/disarming by means of zones, quick

arming, loss of communication with wireless devices, as well as expander troubles

and tampers,

 identifier 3 – arming/disarming and alarm clearing by means of code or proximity card,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info