Bedienungsanleitung Satel Versa Plus (Seite 86 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

84 VERSA Plus SATEL

Options – options related to SIA-IP format:

Send MAC address – if this option is enabled, the MAC address is sent with event code.

Send timestamp – if this option is enabled, the date and time are sent with event code

(the monitoring station can change the date and time in the control panel).

Encrypt data – if the option is enabled, the data being sent are encrypted, and the date

and time are sent with event code (the monitoring station can change the date and time

in the control panel).

SIA-IP key – the key to encrypt data to be sent using the SIA-IP format.

hex – if the option is enabled, you can enter up to 32 hexadecimal characters as the SIA-IP

KEY

. If the option is disabled, you can enter up to 16 alphanumeric characters as the

SIA-IP KEY.

SIA-IP acct – a string of up to 16 hexadecimal characters, which is used to identify the

control panel for the purpose of reporting in SIA-IP format.

Supervision interval – in the case of reporting in the SIA-IP format, an additional

transmission can be sent at specified intervals to check communication with the monitoring

station. You can program a number of days, hours, minutes and seconds between the

transmissions. Entering zeros only means that no additional transmission will be sent.

11.5 Event codes

For the pulse and Ademco Express formats, it is necessary to program codes which will be

reported to the monitoring station if the defined events occur. An event code consists of 2

hexadecimal characters (digits or letters from A to F). The reported events are those for

which a code different from “00” has been programmed.

For the Contact ID and SIA formats, event codes consistent with format specification are

sent. In case of the CONTACT ID (SELECTED) and SIA (SELECTED), the codes must be

programmed at the events which are to be reported (not the programmed code, but a code

consistent with the format specification will be sent).

11.6 Starting the reporting

1. Get the data necessary to properly start the reporting from the monitoring station

operator:

 depending on the transmission path:

 telephone number of the monitoring station (reporting via analog telephone line,

CSD reporting, SMS reporting, reporting via GSM voice channel),

 server address, TCP port number, S

TATION KEY and ETHM/GPRS KEY (reporting via

Ethernet network and GPRS reporting),

 SMS message format (SMS reporting),

 transmission format required by the monitoring station,

 identifiers assigned to the alarm system,

 list of event codes (not applicable to Contact ID and SIA formats).

2. Determine whether the event codes will be sent to both monitoring stations or to one of

them only (enable one of the options: STATION 1 OR 2, STATION 1, STATION 2, STATION 1

AND

2 or STATION 1 OR 2 (DUAL PATH REPORTING)).

3. Determine whether the number of events from the same source is to be limited (EVENTS

AMOUNT LIMITING

option).

4. Determine when the restore code is to be sent (R

ESTORE AFTER BELL, RESTORE AFTER

DISARM

options).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info