50953
20
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
pag. 18
Manual SA 250
PCG/C SA 250 Manual 27-03-07
Lod . . . stays on display. At switching on the weight signal is too low.
Check the correct position of the weigh platform and possible damage of the
connecting cable and connector.
The loadcell could be damaged.
Execute a new one point adjustment procedure until the point 2 (zero setting).
The scale has been switched on, but zero setting is not possible since the
weight signal is higher or lower as 10% of the scale capacity.
Remove the load on the weigh platform. Check cable and connector.
Execute a new one point adjustment procedure until point 2 (zero setting).
The scale refuses zero setting.
The weight signal is outside the zero setting range(+ and - 2% scale capacity).
Tare function will operate correctly. Switch the scale off and on again so a
new zero (+ and - 10% scale capacity) may be settled.
Reading is gross
negative. Set zero and set tare not possible.
The scale has been switched on with a load on the platform and has set zero
with this load. Thereafter, the load has been removed and now the reading is
gross negative. Switch the scale off and on again with an empty platform.
The load on the platform is higher as the maximum scale capacity: overload.
Remove the load from the weigh platform. Check cable and connector.
The loadcell could be damaged.
The weight signal is far too negative. Check the correct position of the weigh
platform and clean the interior of the platform. Check for damage of the cable
and connector. The loadcell could be damaged.
Execute a new adjustment procedure.
Power supply excitation is too low, battery is empty.
Recharge the battery.
The Hi-Lo function cannot be selected with key F
.
- No weight values has been entered in the Hi-Lo mode.
Enter upper and down limit weight values with the key Hi-Lo.
- The Hi-Lo function is disabled in the USER mode.
The Lock up function cannot be selected with key F
.
- The Lock up function is disabled in the Calibration mode.
No data transmission or printing follows after operating the printer key.
- The transmission function is disabled in the USER mode
- Scale reading is at zero
- Scale reading has not been on zero with standstill after the last transmission.
WEEGTECHNIEK HOLLAND B.V. Website www.weegtechniek.nl Tel +31 36 522 20 30
Patroonsweg 23-27 Email info@ weegtechniek.nl Fax +31 36 522 20 60
3892 DA ZEEWOLDE The Netherlands
Malfunctions and error codes
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satex . . SA 250 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satex . . SA 250

Satex . . SA 250 Bedienungsanleitung - Holländisch - 20 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info