Bedienungsanleitung Scan 1003 (Seite 11 von 44) (Englisch)

745593

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

FLOOR PLATE

If you are placing the stove on a ﬂammable ﬂoor, you must comply with the national and local regulations on the size of any

non-ﬂammable subsurface required to cover the ﬂoor around the stove.

Your local Scan dealer can advise you on regulations concerning protection of ﬂammable materials in the vicinity of your stove.

The ﬂoor plate’s function is to protect the ﬂoor and ﬂammable material against any sparks that may occur.

CONVECTION AIR

The covering must contain holes for convection air. Convection means that there is an air circulation ensuring that the heat is

equally distributed in the room. It is important that the demands concerning convection areas are observed.

¬ Min. area for ingoing convection air: 350 cm

¬ Min. area for outgoing convection air: 500 cm

If there is not enough convection air, the covering may be damaged. Do not obstruct the convection holes.

Convection air grids are available as an accessory.

EXISTING CHIMNEY AND PRE-FABRICATED ELEMENT CHIMNEY

If you intend to connect your stove to an existing chimney, it makes sense to contact an authorised Scan dealer, or a local chim-

ney sweep, for advice. These experts will also let you know if your chimney needs renovating.

¬ When connecting a pre-fabricated element chimney, follow the manufacturer’s connection instructions for the relevant

chimney type

CONNECTION BETWEEN BUILT-IN STOVE AND STEEL CHIMNEY

Your Scan dealer, or local chimney sweep, can advise you on choosing a make and type of steel chimney. This ensures that the

chimney will match your wood-burning stove.

REQUIREMENTS FOR CHIMNEY

The chimney must have a diameter of min. 148 mm and be labelled T400 and G for soot testing. The length must be min. 4,5

metres.

If you opt to connect the bulit-in stove with an elbow pipe, you should use a curved elbow, as this gives a better draught.

If you connect the stove with a sharp elbow pipe, the cleansing lid must be placed in the vertical part so that the

horizontal part can be cleaned through here.

The requirements to the chimney and the ﬂue pipe in terms of safety distances must be met.

¬ Choosing the wrong length or diameter of chimney could impair functionality

¬ Always comply exactly with the instructions provided by the chimney supplier

INTERNAL INSTALLATION IN NON-FLAMMABLE MATERIAL

When building or ﬁtting into structures that do not contain ﬂammable materials, a minimum distance of 10 mm must be main-

tained between the brickwork and the convection hood. This is to prevent cracks in the brickwork caused by the expansion of the

metal while the stove is heating. This construction does not require convection grates except for the convection air produced by

the convection box of the insert. However, please note that without convection grates, the effect of the insert will be lower.

(BY BUILDING INTO FLAMMABLE MATERIAL WITH FIRE WALL)

/ EXISTING BRICKWORK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 1003 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 1003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info