Bedienungsanleitung Scan 1003 (Seite 35 von 44) (Englisch)

745593

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

The various woods have different caloriﬁc values. In other words,

for certain species of wood, you will need to use a greater quantity

to achieve the same heating performance. This Instuction Ma-

nual assumes that you will be using beach, which has a very high

caloriﬁc value and is also the easiest wood to get hold on. If you

use oak or beech as fuel, you need to bear in mind that these

wood types have a greater caloriﬁc value than for example birch.

To avoid any risk of damage to the stove, you should therefore

make sure to use less fuel in these cases.

CALORIFIC VALUE OF THE WOOD

Wood types kg Drywood/m

Compared to beech

Hornbeam 640 110%

Beech/Oak 580 100%

Ash 570 98%

Maple 540 93%

Birch 510 88%

Pine 480 83%

Fir 390 67%

Poplar 380 65%

HANDLING OF THE FUEL

SELECTING WOOD/FUEL

You can use any type of wood as fuel. However harder woods, such as beech or ash, are generally better for heating, as they burn

more evenly and create less ash. Other woods, such as maple, birch and spruce, are excellent alternatives.

PREPARATION

The best fuel is obtained where the tree has been felled and the wood sawn and split before May 1st. Remember to cut the wood

to match the size of the combustion chamber. We recommend a diameter of 6-10 cm. The length should be about 6 cm shorter

than that of the combustion chamber to leave enough space for air to circulate. If the diameter of the wood is greater than the

above, it should be split down its length. Wood that has been split dries faster.

STORING

You need to store the sawn and split wood in a dry place for 1-2 years before it will be dry enough to burn. Wood dries faster if

you stack it in an airy place. Before using it, it is a good idea to store the wood for a few days at room temperature. Remember

that wood absorbs moisture from the air during autumn and winter.

MOISTURE

To avoid problematic impact on the environment and to ensure optimum operating economy, the wood should be perfectly dry

before it can be used as fuel. If you use wood that is too damp, most of the heat it produces will be used up in evaporating the

water. The stove will accordingly not increase in temperature, nor emit heat to the room as a result. This is obviously poor econ-

omy, and it will cause soot build-up on the glass pane, in the stove and in the chimney. Operation using moist wood also pollutes

the environment.

¬ Maximum wood moisture content should not exceed 20%. A moisture content of 15-18% will deliver best efﬁciency

¬ An easy way of checking wood moisture content is to knock the ends of the two pieces of wood together. If the wood is moist,

the sound will be slightly mufﬂed

¬ It is a good idea to take the wood into the house a day before it is to be used

USE OF THE FOLLOWING AS FUEL IS ILLEGAL

NOTE: It is absolutely prohibited to ﬁre with painted, pressure impregnated or glued wood or sea driftwood. Nor should you

ever burn chipboard, plastics, waste or treated paper. These contain substances that are hazardous to human health, to the

environment, your stove, and your chimney. In short - make sure you only use proper wood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 1003 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 1003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info