Bedienungsanleitung Scan 1005 (Seite 33 von 44) (Englisch)

745595

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

CONTINUOUS OPERATION

It is important to obtain as high a temperature as possible in the combustion chamber. This results in best possible use of the

stove and fuel, as well as achieving clean combustion. In this way you will avoid build-up of soot on the combustion chamber

lining and glass pane. During operation, you should not see any smoke; just a movement in the air that indicates combustion is in

progress.

¬ After completing the lighting phase, you should have a good layer of embers in the stove; you can then start operation of it

properly.

¬ Add two pieces of wood at a time: they should be about 1 kg in weight and about 25-40 cm long

NOTE: The wood must catch ﬁre quickly. This is why we recommend setting the primary air ﬂow fully open. Operating the stove

at too low a temperature and with too little primary air can lead to gases igniting, which can damage the stove.

¬ When adding wood, always open the glass door carefully to prevent smoke escaping. Keep the door closed during the whole

combustion phase

¬ Never add wood, while the fire is burning nicely

At the EN 13229-test the stove was fired as shown on the picture:

With three pieces of birch each 210 mm – with a total weight of 1.45 kg.

Primary air damper 0% open – secondary air damper 90% open.

WARNING ABOUT OVER-FIRING

If the stove is continiously ﬁred with larger amounts of wood than recommended and/or receives too much air, this can cause

a heavy heat development liable to damage both stove and the surrounding walls. We therefore recommend that you always

observe the max. recommended amount of fuel (See under ”Technical Data”).

USING THE STOVE IN VARIOUS WEATHER CONDITIONS

The way the wind affects the chimney can have a big impact on how your stove reacts under various wind loads; you may need to

adjust the airﬂow to achieve good combustion. Fitting a damper in the ﬂue pipe may also help, as it will allow you to regulate the

draught under changing wind loads.

Fog and mist can also have a big impact on chimney draught; you may need to use other settings for the combustion air to

achieve good combustion.

FIRING IN THE SPRING OR AUTUMN

In the spring/autumn transition period, where there is less need for heating, we recommend you light the stove “top down” once,

perhaps adding just two pieces of wood to ensure that the combustion chamber lining burns clean again.

GENERAL NOTES

PLEASE NOTE! Parts of the wood-burning stove, especially the outer surfaces, become hot during use. Due care should be

exercised.

¬ Never empty ashes into a ﬂammable container. Ashes can contain glowing embers long after you ﬁnish operating the stove

¬ When the stove is not in use you can close the dampers to avoid a draught through the stove

¬ If the stove has not been used for some time, you should check the ﬂue passageways for potential blockages before relighting

¬ We advise you strongly not to use the insert over night. The insert is not suited for this purpose

NOTE: Never place ﬂammable material in the radiation zone of the stove!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 1005 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 1005

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info