Bedienungsanleitung Scan 5001 (Seite 8 von 32) (Englisch)

745581

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ASSEMBLY

DISPOSAL OF PACKAGING

Your Scan built-in stove may come supplied with the following packaging:

Wood packaging The wood packaging can be reused and after final use can be incinerated as a CO2 neutral

product or sent for recycling.

Flamingotop Send for recycling or waste disposal

Foam Send for recycling or waste disposal

Plastic bags Send for recycling or waste disposal

Stretch/plastic ﬁlm Send for recycling or waste disposal

FRESH AIR INTAKE

In a well-insulated house the air used for the combustion process has to be replaced. This particularly applies to houses

with mechanical ventilation. There are different ways of making sure that air is exchanged. The most important thing is to

ensure that there is a supply of air to the room where the built-in stove is located. The external wall vent must be located

as close to the stove as possible, and you must be able to close it when you are not using the stove. National and local

building regulations must be followed with regard to connection of a fresh air intake.

The diameter of the connection piece for fresh air is 120 mm. If you want to use a 100 mm connection tube you can mount

a gasket on the outside of the tube before mounting the tube inside the connection piece.

CLOSED COMBUSTION SYSTEM

You should use the closed combustion system for the built-in stove if you live in a newly-built, airtight home.

External combustion air is connected through a ventilation pipe via the wall or ﬂoor.

It must be possible to shut off the ventilation pipe with a valve, when the stove is not in use. Minimum Ø 100 mm ventila-

tion pipe, maximum length: 6 metres with a maximum of one bend. We recommend smooth steel pipes.

If you want external combustion air at the rear, you must close the hole in the bottom with the dismounted cover plate.

NOTE: if the stove has a fresh air connexion or closed combustion, the ventilation pipe must be open, when the stove is in use!

LOAD-BEARING SUBSURFACE

All items in our product range come under the category of lightweight ﬁreplaces and stoves and do not normally require

any reinforcement of the beam structure. They can be positioned on ordinary beams/ﬂoor.

You should of course make sure that the subsurface on which the stove is positioned can indeed support the weight of the

stove and, where applicable, a steel chimney, if you have opted for this solution.

FLOOR PLATE

If you are placing the stove on a ﬂammable ﬂoor, you must comply with the national and local regulations on the size of

any non-ﬂammable subsurface required to cover the ﬂoor around the stove.

Your local Scan dealer can advise you on regulations concerning protection of ﬂammable materials in the vicinity of your stove.

The ﬂoor plate’s function is to protect the ﬂoor and ﬂammable material against any sparks that may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 5001 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 5001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info