Bedienungsanleitung Scan 5001 (Seite 24 von 32) (Englisch)

745581

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

REFUELLING

It is important to obtain as high a temperature as possible in the combustion chamber. This results in best possible use

of the stove and fuel, as well as achieving clean combustion. In this way you will avoid build-up of soot on the combustion

chamber lining and glass pane. During operation, you should not see any smoke; just a movement in the air that indicates

combustion is in progress.

¬ After completing the lighting phase, you should have a good layer of embers in the stove; you can then start

operation of it properly.

¬ Add 2-3 pieces of wood at a time: they should be about 0.5 kg in weight and about 30 cm long.

NOTE: The wood must catch ﬁre quickly. This is why we recommend setting the combustion air ﬂow fully open.

NOTE: Operating the stove at too low a temperature and with too little combustion air can lead to gases igniting, which

can damage the stove.

¬ When adding wood, always open the glass door carefully to prevent smoke escaping. Never add wood, while

the fire is burning nicely.

WARNING ABOUT OVER-FIRING

If the stove is continiously ﬁred with larger amounts of wood than recommended and/or receives too much air, this can

cause a heavy heat development liable to damage both stove and the surrounding walls. We therefore recommend that

you always observe the max. recommended amount of fuel (See under ”Technical Data”).

THE FUNCTION OF THE CHIMNEY

The chimney is the built-in stove’s motor; its performance determines how well your stove will work. The draught in the

chimney creates negative pressure in the wood-burning stove. The negative pressure draws the smoke out of the stove

and takes in air through the combustion air damper to fuel the combustion process. Combustion air is also used for the

airwash system that keeps the glass clear of soot.

The draught in the chimney is created by the difference in temperature inside and outside the chimney. The higher the

difference in temperature, the better the draught. This is why it is important that the chimney reaches operating tem-

perature before you reduce the damper settings to restrict combustion in the stove (a brickwork chimney will take longer

to reach operating temperature than a steel chimney). It is very important that the operating temperature is reached as

quickly as possible on days when the draught in the chimney is poor due to unfavourable wind and weather conditions.

You need to get a few ﬂames going as quickly as possible. Chop the wood extra thin; use an extra ﬁre lighter etc.

¬ After longer periods without use, you must check the chimney ﬂue for blockages.

¬ You can connect several units to the same chimney. You should however ﬁrst check the relevant regulations in

this respect.

USING THE STOVE IN VARIOUS WEATHER CONDITIONS

The way the wind affects the chimney can have a big impact on how your stove reacts under various wind loads; you may

need to adjust the airﬂow to achieve good combustion. Fitting a damper in the ﬂue pipe may also help, as it will allow you

to regulate the draught under changing wind loads. The damper must not close more than 80% of the ﬂue pipe.

Fog and mist can also have a big impact on chimney draught; you may need to use other settings for the combustion air to

achieve good combustion.

GENERAL NOTES

PLEASE NOTE: parts of the built-in stove, especially the outer surfaces, become hot during use. Due care should be exer-

cised Never place ﬂammable material in the radiation zone of the stove!

¬ Never empty ashes into a ﬂammable container. Ashes can contain glowing embers long after you ﬁnish operating the stove.

¬ When the stove is not in use you can close the dampers to avoid a draught through the stove.

¬ If the stove has not been used for some time, check the ﬂue passageways for potential blockages before relighting.

CHIMNEY FIRE

In the event of a chimney ﬁre, keep the stove door, ash drawer, and all dampers on the stove closed. In an emergency, call

the ﬁre service.

¬ We recommend that you get a chimney sweep to check the chimney before using the stove again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 5001 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 5001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info