Bedienungsanleitung Scan 5002 (Seite 9 von 32) (Englisch)

745582

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

CONVECTION AIR

The covering must contain holes for convection air. Convection means that there is an air circulation ensuring that the

heat is equally distributed in the room. It is important the demands concerning convection areas are observed.

¬ Min. area for ingoing convection air: 500 cm

¬ Min. area for outgoing convection air: 750 cm

If there is not enough convection air, the covering may be damaged. Convection air grids are available as an accessory.

EXISTING CHIMNEY AND PRE-FABRICATED ELEMENT CHIMNEY

If you intend to connect your stove to an existing chimney, it makes sense to contact an authorised Scan dealer, or a local

chimney sweep, for advice. These experts will also let you know if your chimney needs renovating.

¬ When connecting a pre-fabricated element chimney, follow the manufacturer’s connection instructions for the

relevant chimney type.

CONNECTION BETWEEN BUILT-IN STOVE AND STEEL CHIMNEY

Your Scan dealer, or local chimney sweep, can advise you on choosing a make and type of steel chimney. This ensures that

the chimney will match your wood-burning stove.

REQUIREMENTS FOR CHIMNEY

The chimney must have a minimum internal diameter of 148 mm and have a T400 designation, with G for the soot ﬁre test.

The length must be min. 3,5 metres.

If you opt to connect the bulit-in stove with an elbow pipe, you should use a curved elbow, as this gives a better draught.

If you connect the stove with a sharp elbow pipe, the cleansing lid must be placed in the vertical part so that the

horizontal part can be cleaned through here.

The requirements to the chimney and the ﬂue pipe in terms of safety distances must be met.

¬ Choosing the wrong length or diameter of steel chimney could impair functionality

¬ Always comply exactly with the instructions provided by the steel chimney supplier

BALANCED FLUE

If the stove is connected with a balanced ﬂue, we recommend the use of a 100 mm Lindab tube and a chimney length of

min. 4.5 m.

MINIMUM DISTANCE TO FLAMMABLE MATERIALS

Distance to side: 400 mm - back: 400 mm - glass: 800 mm. - ceiling: 1000 mm.

You should however assess whether furniture or other items might become excessively dry due to being too close to the

stove.

¬ The stove is NOT to be built into ﬂammable materials without the use of a ﬁre wall and heat shields!

INTERNAL INSTALLATION IN NON-FLAMMABLE MATERIAL

When building or ﬁtting into structures that do not contain ﬂammable materials, a minimum distance of 10 mm must

be maintained between the brickwork and the convection hood. This is to prevent cracks in the brickwork caused by the

expansion of the metal while the stove is heating. This construction does not require convection grates except for the

convection air produced by the convection box of the insert. However, please note that without convection grates, the

effect of the insert will be lower.

BUILDING IN THE STOVE AT A FIRE WALL

We refer to the building sketches on page 11.

/ EXISTING BRICKWORK

(WHICH IS NOT PROTECTED BY FIREWALL)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 5002 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 5002

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info