Bedienungsanleitung Scan 5004 FRL (Seite 26 von 40) (Englisch)

745585

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Place the ﬁre lighters

between the upper sticks

INSTRUCTIONS FOR HEATING

ENVIRONMENTALLY FRIENDLY OPERATION

Avoid turning down your wood-burning stove to the point where no ﬂames are

visible from the wood, as this leads to poor combustion and low efﬁciency. The

gases released from the wood will not be burnt off due to the low temperature

in the combustion chamber. Some of the gases will condense in the stove and

ﬂue system as soot, and this could lead to your chimney catching ﬁre at a later

point. The residual smoke which exits the chimney will pollute the surrounding

area and cause an unpleasant smell.

LIGHTING

We recommend the use of ﬁre lighters, or similar products, which are available from your Scan dealer.

Using ﬁre lighters helps light the wood more quickly and keeps the combustion process clean.

See our video about correct ﬁring on www.scan.dk or scan the QR-code. Please note that this

video is only intended as a guide. You should also follow the instructions in the speciﬁc manual

for your stove model!

NOTE: Never use liquid lighting fuels!

”TOP DOWN” LIGHTING

"Top down" lighting is a more environmentally friendly way of lighting the ﬁre and helps to keep the glass area as clean as possible.

Do as follows for a correct ”top down” lighting:

¬ 4 pieces of wood approx. 25-30 cm long with a weight of approx. 0.4-0.6 kg per piece.

¬ 12-20 thin pieces of ﬁrewood of about 25-30 cm in length, with a total weight of approx. 1 kg.

¬ 3-4 ﬁre lighters

1 Place the pieces of wood, ﬁrewood and ﬁre lighters in the combustion chamber as shown below

2 Set the combustion air control to maximum for 20-30 minutes (See "Instructions for use")

When the large pieces of wood have caught ﬁre, you can adjust the combustion air to the desired level

NOTE: The wood must not cover the bottom entirely and must never be placed higher than the indication for max. load

(This does not apply at a cold start) (See Maintenance).

NOTE!

No matter how good your chimney is,

it will not perform well, if you do

not use it correctly. Equally, a poor

chimney may well give you acceptable

results, if you use it correctly

Scan the QR-code

and see our video

about correct ﬁring.

USING THE STOVE IN VARIOUS WEATHER CONDITIONS

The way the wind affects the chimney can have a big impact on how your stove reacts under various wind loads; you may need to

adjust the airﬂow to achieve good combustion. Fitting a damper in the ﬂue pipe may also help, as it will allow you to regulate the

draught under changing wind loads. The damper must not close more than 80% of the ﬂue pipe.

Fog and mist can also have a big impact on chimney draught; you may need to use other settings for the combustion air to

achieve good combustion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 5004 FRL Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 5004 FRL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info