Bedienungsanleitung Scansonic IN300 (Seite 5 von 17) (Englisch)

638438

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

SET UP & CONNECTION

Mains Connection

1. Connect the AC power cord to the unit via the AC socket at the back.

2. Plug the AC power cord to the AC mains outlet.

Network Connection

Wired network

1. Check rst of all whether the control lamps (LINK/ACT) of your LAN connection or your router light up.

2. Use an Ethernet cable with RJ45 connector to connect the NETWORK socket of the radio with the LAN port of your

router.

3. Proceed for the operation as described in the below “GETTING STARTED”. But no need to run through the setup

wizard.

Note: Information on the LAN connection can be obtained from the user manual of the router manufacturer.

Wireless network

1. Check rst of all whether the control lamps (LINK/ACT) of your WLAN connection or your router light up.

2. Proceed for the operation as described in the below “GETTING STARTED”. It is highly recommended to run through

the setup wizard in the system settings section.

Note: Information on the WLAN/WiFi network connection can be obtained from the user manual of the router manufacturer.

Walls or other obstacles may inuence the WiFi range. Try to nd the best location to avoid interruption and

interference while operating.

GETTING STARTED

Press the “

” button once to switch on the radio, the display will show the main menu. To go to a function or open a sub-

menu, rotate the SCROLL control followed by pressing on it to conrm. Each function is selected via a menu consisting of

several levels.

Main menu

The following modes can be selected in the main menu:

Internet radio, Music player, FM radio, AUX in, Sleep, Alarms, System settings.

To select your desired function, rotate the SCROLL control followed by pressing on it to conrm.

System settings

Set up wizard

The setup wizard is available in the system settings section, you can run through this to congure settings for date/time

and network, once this has nished, your radio is ready to use.

Note: No need to run through the setup wizard if a wired network is used.

◊ 2/24 hour display

To select your preference between 12 and 24 hour clock display format - rotate the SCROLL control followed by pressing

on it to conrm.

◊ Time/Date

The time and date can be manually set or automatically via the network or FM.

Auto update

The auto update works with data sent over FM or the Internet. The clock is only updated when in a corresponding mode,

so it is recommended to select a mode that you use regularly.

1. Select auto update from FM or Network.

2. Select the appropriate time zone if the auto update is done by the Internet.

3. If your country uses daylight saving, the automatically update time may be wrong by one hour. Set the daylight savings

to ON when daylight savings are in effect.

Manual set

1. If “No update” is selected, the wizard will prompt you to set the time and date

manually. The date and time are displayed in dd-mm-yyyy and hh:mm AM/PM

format.

2. The value to be set will ash, rotate the SCROLL control to adjust the value

followed by pressing on it to go for the next setting, rst set the date then nally

the time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scansonic IN300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scansonic IN300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info