Bedienungsanleitung Schaerer Siena 1 (Seite 10 von 35) (Englisch)

458914

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

www.schaerer.comProduct description

Operating instructions / V07 / 06.2010

43 / 68

Power supply

Model Power rating

Fuse (installa-

tion site)

Siena

Siena 2

220-230V~ 50/60 Hz 2000-2200 W 10-16A

200V~ 50/60 Hz

2200W 10-16A

240V~ 50/60 Hz

100V~ 50/60 Hz

1200W 16A

110V~ 50/60 Hz

120V~ 50/60 Hz

130V~ 50/60 Hz

The device must be electrically connected according to all valid regulations (VDE 0100) as well as national

stipulations. The type of power cable must be at least H 05 VV-F. The voltage specied on the serial plate

must match the supply voltage at the installation location.

● The phase must be protected from short-circuits with the Ampere value mentioned on the serial

plate!

All poles of the device must be able to be disconnected from the power supply. ●

Never operate a device with a faulty power cord. Have a defective power cord or plug replaced ●

immediately by a qualied service technician.

Schaerer Ltd. advises against the use of extension cables! • If an extension cable must be used, ●

nevertheless (minimum cross-section: 1.5 mm2), please observe the cable manufacturer’s data

(instructions for use) and all local regulations.

Power cords must be connected in such a way that no one can trip over them. Do not pull the ●

cords over corners or sharp edges, pinch them between objects or allow them to hang loosely

in a room.

Do not place cables over hot objects, and protect them from oil and aggressive cleaning ●

agents. Never lift or pull the device by its power cord. Never pull the plug out of the socket

by its cord. Never touch the power cord or plug with wet hands! Never insert a wet plug into a

power socket!

Water connection / draining (option)

The water supply connection must be made in accordance with the applicable requirements and the regu-

lations of the respective country.

If the machine is connected to a newly installed water pipe, the pipe and the supply tube must be thor-

oughly rinsed so that no dirt particles can enter the machine. The coffee maker must be connected to an

installed drinking-water pipe with shutoff valve. The machine is installed by using the mounted pressure

tube and the G 1/4“ screw at the pressure relief component mounted to the tap (set to 0.2 MPa (2 bar)). If

the machine is attached to a water drainage system, the supplied temperatureresistant drain hose must

be connected to the drip pan and siphon. It must be rmly attached to the drain and slanted at a downward

angle (so that the water can ow downward).

Always use the new hose set (fresh water/outlet hose) provided with the machine!

The ideal hardness of the water is 5 – 6 °dH (German hardness) or 8 – 10 °fH (French hardness). The

chlorine content should not exceed 100 mg per litre. Ideal Ph value = 7. Otherwise, the local regulations

are binding

Water pressure

Recommended: 0.1-0.3 MPa (1-3 bar)

Maximum: 0.6 MPa (6 bar)

Water ingress temperature

Minimum: 5 °C

Maximum: 30 °C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schaerer Siena 1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Schaerer Siena 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info