Bedienungsanleitung Scheppach AB1500MAX (Seite 15 von 48) (Deutsch, Englisch, Französisch, Polnisch)

781883

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

15 І 48

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Starting the equipment

Using the chisel Fig. 2

• Clean the tool before tting it and apply a thin coating

of grease to the tool shaft.

• Pull back the SDS MAX chuck lock (4) as far as pos-

sible. Insert the chisel as far as possible and turn it

until it locks.

• Release the SDS MAX chuck lock. It should only be

possible to move the chisel in the drill chuck by ap-

proximately 1 cm forwards or backwards.

• Check the lock by pulling the tool.

Removing the tool

To remove the tool, proceed in reverse order.

Turn the tool Fig. 3

To turn the tool into the correct position, the rear

unlocking ring (a) must be pulled and held. After this

the tool can be rotated to the desired position. To x the

position release the release ring (a) and insure that it is

reliably locked.

Additional handle Fig. 2

For safety reasons you must only use the demolition

hammer with the additional handle.

The additional handle (3) enables you to achieve better

stability whilst using the demolition hammer.

For safety reasons the machine must not be used with-

out the additional handle (3).

The additional handle can be turned into any required

position. Undo the lock of the additional handle (3) by

turning the handle (3) counterclockwise. Then turn the

handle (3) into the most comfortable working position

and tighten the handle (3) by turning it clockwise.

Operation / Work instructions

Caution! For your safety, the machine must be held

only at the two handles (1 and 3, Figure 1)!

This will avoid the danger of an electric shock through

contact of lines during chiselling.

Switching on / off (Fig. 4)

This power tool works with torque switching.

Warning! Hold power tool safely on the main and ad-

ditional handle! Press until the power button! Otherwise

there is a risk of injury!

Hold power tool safely in vertical position on the main

and additional handle.

To switch on: Press the control switch (2).

To switch off: Release the control switch (2).

• For continuous operation, press the on/off switch (2)

and the locking button (b) on the handle at the same

time.

• To switch off continuous operation, press the on/off

switch (2) and then release it again.

Always keep the chiselling tools sharp.

Note:

–Work only at low pressure when chiselling

–Excessive pressure loads the motor unnecessarily.

–Sharpen the chisels in time and replace, if necessary.

Replacing the power cable

If the power cable for this equipment is damaged, it

must be replaced by the manufacturer or its aftersales

service or similarly trained personnel to avoid danger.

Cleaning and maintenance

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it with com-

pressed air at low pressure.

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these could attack the plastic parts of the equip-

ment. Ensure that no water can seep into the device.

Carbon brushes

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important! The

carbon brushes should not be replaced by anyone but

a qualied electrician.

Maintenance

There are no parts inside the equipment which require

additional maintenance.

Disposal and recycling

The unit is supplied in packaging to prevent its being

damaged in transit. This packaging is raw material and

can therefore be reused or can be returned to the raw

material system.

The unit and its accessories are made of various types

of material, such as metal and plastic. Defective com-

ponents must be disposed of as special waste. Ask your

dealer or your local council.

Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing tempera-

ture. The ideal storage temperature is between 5 and

30 °C. Store the electric tool in its original packaging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach AB1500MAX Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info