Bedienungsanleitung Scheppach ASP50-ES (Seite 18 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Finnisch)

781452

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

18 | GB

Installing the machine head (2) and the handle (1)

(g. 7)

• Place the machine head (2) on the stainless steel

container (15). Secure the machine head (2) with

the locking hooks (5). When installing the machine

head (2), ensure that the locking hooks (5) latch into

place correctly.

• Place the handle (1) on the machine head (2) and

fasten it with two screws (28) with a screwdriver

(not included in the delivery).

Installing the drain hose (11) (g. 8, 9, 10)

• Thread the retaining clip (13) over the drain hose

(11). (Fig. 8)

• Fit the drain hose (11) to the drain hose connec-

tion (14). Position the retaining clip (13) such that it

fastens the drain hose (11) to the drain hose con-

nection (14). Tighten the retaining clip (13) with a

screwdriver (not included in the delivery). (Fig. 9)

• At the other end of the drain hose (11) there is a

stopper (7) which must be closed during suction

operation. The drain hose can also be fastened at

the drain hose holder (8). (Fig. 10)

Installing the foam lter (22) (g. 3, 11)

Never use the device without lter! Always ensure

that the lters are correctly tted!

• Installing the foam lter (22): For wet vacuuming,

slide the foam lter (22) provided over the lter bas-

ket with safety oat valve (20).

Installing the folded lter (24) (g. 3, 12)

For dry vacuuming, slide the folded lter (24) provided

over the lter basket with safety oat valve (20). The

folded lter (24) is only suitable for dry vacuuming!

Installing the paper lter bag (23) (g. 3, 13)

It is recommended to use an additional paper lter

bag (23) when vacuuming ne, dry dirt.

• Slide the paper lter bag (23) over the suction open-

ing in the stainless steel container (15). The paper

lter bag (23) is only suitable for dry vacuuming.

The paper lter bag (23) makes it easier to dispose

of the dust collected.

Installing the suction hose (21) (g. 3, 14, 15)

Connect the suction hose (21) to the corresponding

port, depending on the desired use, on the wet and

dry vacuum.

Vacuuming:

Connect the suction hose (21) to the suction hose port

(16). To do so, slide the end of the suction hose (21)

with the two nipples into the suction hose port (16)

(A). Insert the two nipples into the recesses. Once

the suction hose is fully inserted, turn it clockwise (B).

m WARNING!

This electric tool generates an electromagnetic eld

during operation. This eld can impair active or pas-

sive medical implants under certain conditions. In

order to prevent the risk of serious or deadly injuries,

we recommend that persons with medical implants

consult with their physician and the manufacturer

of the medical implant prior to operating the elec-

tric tool.

6. Technical Data

Mains voltage 220-240 V~ 50/60 Hz

Power 1400 W

Maximum device socket

power 2000 W

Total power 3400 W

Water tank capacity 50 L

Suction performance 19Kpa

Protection category IPX4

Protection class I

7. Installation

m IMPORTANT!

Prior to use, ensure that the device has been cor-

rectly and fully assembled.

Unpacking (g. 1, 2, 3)

• Release the locking hooks (5) and remove the ma-

chine head (2). The accessories are located inside

the stainless steel container (15). Only the metal

extension tube (27) is located outside the stainless

steel container (9) in the packaging. Remove all of

the accessories from the stainless steel container

(15).

Fitting the wheels with axle (9) and the castors

(12) (g. 4, 5).

• Place the wheels with axle (9) into the recesses

provided on the wheel mounting base (10). Fas-

ten the wheels with axle (9) with the screws for the

axle-mounted wheels (29) with the help of a screw-

driver (not included in the delivery).

• Press the two castors (12) into the holes in the

wheel mounting base (10).

Installing the push grip (4) (g. 6)

• Push the push grip (4) into the push grip mount (6)

on the stainless steel container. In doing so, ensure

that the push grip (4) latches into place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach ASP50-ES Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info