Bedienungsanleitung Scheppach Basa 4.0 (Seite 12 von 26) (Deutsch, Englisch, Französisch)

782164

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Warning Symbols / Warning Notes 

Read the handbook before start-up

Use hearing protection and safety

glasses

Only for EU countries

Do not throw electronic tools in the

household garbage!

According to the European Directive

2002/96/EG on restriction of hazar-

dous substances and implementation

in national law, worn-out electronic

tools must be collected separately

and transported to an environmentally

sound recycling

Residual Risks 

• The machine is built according to the state of

the art and the recognized safety-technical

rules. Nevertheless, individual residual risks

can arise during operation.

• Danger of injury to fingers and hands from

the rotating saw blade due to improper gui-

ding of the work piece.

• Injuries from the work piece being flung away

due to improper holding or guiding, such as

work without a fence.

• Danger to health from sawdust or wood

chips. It is imperative that the operator wear

personal protective equipment like eye

protection and dust masks. Install suction

system!

• Injuries from defective saw band. Check the

saw band regularly for integrity.

• Injury danger to fingers and hands during

saw band exchange. Wear suitable work

gloves.

• Injury danger while switching on the machine

from the saw band turning on.

• Danger from current when using improper

electrical connection leads.

• Hearing damage. Wear suitable hearing

protection.

• Never clean the band saw blades while the

machine is running.

• Danger to health from the running saw blade

with long hair and loose clothing. Wear per-

sonal protective equipment such as a hair net

and close-fitting work clothes.

• Moreover, in spite of all preventative

measures being taken, unforeseeable residu-

al risks can still arise.

• Residual risks can be minimized if the

“Safety Notes” and “Intended Use” as well

as the operating instructions as a whole are

observed.

Transport

The machine may be transported only with suita-

ble lifting devices (crane or lift truck). The upper

band wheel box is to be used as the sling point for

the cable.

Never lift the saw table!

Using the transport device (Accessory Art.

No.: 7901504701)(Fig. 1):

To use the transport device, insert the transport

handle (A) in the transport handle opening.

(After inserting the transport handle (A), turn it a

bit so that it cannot slide out)

Now lift the machine on the transport handle (A)

far enough that the machine stands on the two

rear wheels (B) and can be moved.

Pay attention to the machine’s high centre of

gravity (top-heavy)

Set-up / Storage

Prepare the work station at which the machine

should stand. Create enough space to enable

safe, uninterrupted work. The machine is designed

for work in enclosed spaces and must be set up in

a stable manner on a level, firm base. At least two

people are required to lift down the pallet. Based

on the work setting, tip the machine to the left and

pull out the pallet to the right.

To prevent the machine from slipping, it is possible

to screw it to the floor. Through-holes are attached

to the floor plate for this purpose.

Storage requirements:

Make sure that the machine is stored in a dry

place.

Minimum temperature: +5°

Maximum temperature: +40°

Start-up

Your machine is delivered completely assembled;

nevertheless, it may be that you still need to make

small adjustments.

Check the saw band tension before every

start-up

Operating requirements:

Make sure that the machine is operated in a dry

place.

Minimum temperature: +5°

Maximum temperature: +40°

Saw band

The selection of the right saw band is crucial for

the cutting performance.

Pay attention to the table for selection of the saw

bands in the operating instructions.

With small saw bands, you can cut smaller radii

than with wide saw bands.

Use only well-sharpened, flawless saw bands.

Defective saw bands increase the risk of acci-

dents and reduce work performance

Changing the saw band

Caution: Pull out the plug!

• Open the saw band guard. To do this, open

the closing knob (Fig.2 “A”). Now open the

star grip screw (Fig.2 “B”) far enough that

the door can be opened. This star grip screw

simultaneously operates the end switch that

prevents the saw from turning on while the

door is open.

• To prevent the door from falling shut, unfold

the bar (Fig.3 “A”).

• Also open the adjustable saw blade guard

(Fig.2 “C”).

• To relax the band wheel, use the quick

release skewer (Fig.4 “A”) (move the lever

clockwise).

• Unfold the guide pipe for the longitudinal

fence so that you can pull out the saw band.

Open the 4 wing screws (Fig.5 “A”) in order

to be able to unfold the guide pipe.

• Insert the new saw band.

• Turn the band wheel manually in the cutting

direction and adjust the final tension with

the hand grip at the same time. The tension

depends on the saw band width. Wide saw

bands are to be tensioned more strongly

than small ones. For fine adjustment of the

saw band tension, use the adjustment screw

(Fig.4 “B”).

• Caution: Too high tension leads to early

breakage! Always relax the saw band after

ending the band saw work! To do this, use

the hand grip (Fig.4 “A”).

Side correction

• The saw band should run about in the middle

of the band wheels.

• Turn the upper band wheel by hand in the

cutting direction and carry out the side cor-

rection with the hand grip (Fig.4 “C”).

• After successful adjustment, tighten the wing

nut on the hand grip.

You can adjust the upper saw band guide up to

250 mm work piece height (Fig. 6). Keeping the

distance to the work piece as small as possible to

ensure optimal band guidance and safe work!

DGB

Scheppach Basa 4.0 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info