Bedienungsanleitung Scheppach Basa 7.0 (Seite 16 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

782165

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

DGB

Symbols

Remaining hazards

• The machine has been built using modem

technology in accordance with recognized sa-

fety rules. Some remaining hazards, however,

may still exist.

• The moving saw belt can cause injuries to

ngers

and hands when the work piece is not cor

rectly fed.

• Thrown work pieces can lead to injury if the

work piece is not properly secured orfed, such

as working without a limit stop.

• Wood chips and sawdust can be health

hazards.

Be sure to wear personal protective gear such

as safety goggles. Use a vacuum exhaust

system.

• Defective saw blades can cause injuries.

Regularly inspect the structural integrity of

sawblades.

• Danger of injury to ngers and hands when

changing the saw band. Wear suitable work

gloves.

• The use of incorrect or damaged mains cables

can lead to injuries caused byelectricity.

• Danger of injury when switching the machine

on due to start-up of saw band.

• Long hair and loose clothing can be hazard-

dous when the belt saw is in motion. Wear

personal protective gear such as a hair net

and tight tting work clothes.

• Even when all safety measures are taken,

some remaining hazards which are not yet

evident may still be present.

• Remaining hazards can be minimized by

following the instructions in „Safety Precau-

tions“, „Proper Use“ and in the entire operating

manual.

Transport

The machine may only be transported with

suitable

lifting devices (crane or fork lift). The connection

point for the rope (crane) is on the upper band

wheel cabinet.

Never lift trom the saw bench.

If the machine is to be moved frequently within

the

work area, use of the wheel assembly special

accessory is recommended.

Montage

The machine is not completely assembled

for reasons of transport.

Assembly tools:

13 mm fork wrench

5 mm hexagonal socket wrench

(not included in delivery)

Guide pipe

Fig.“2“

The fence plate underneath the sawblade

has been tted in the works.

Before attaching the guide tube, check

the fence plate for tight t.

If necessary, tighten the clamping levers (1).

Fit the steel holding devices for the guide tube at

the lett and right-hand side of the fence plate.

2 cheese head srews M8 x 16

2 washers

2 steel holding devices

Push the gu!de lube mto the holding devices

from the side. Before tightening the hexagon

boIts, check the parallelity of the guide tube

with the table (dimension „x“).

Dimension „x“ must be identical at the front

and at the rear of the table.

Fence

Fig. „3“

• The fence can be used to the Ieft or

the right of the saw band depending

on wone requirements.

Screw together the feace pipe, intermediate

plate, and guide slide (handscrewed). To da this,

insert both threaded screws into the guide slots.

4 washer 6

4 cheese head screws M6x20

• The divider plate to carry the fence is

screwed onto the fence pipe on the

right or the Ieft depending on the work

requirements.

Do not tighten the wing nuts!

2 saucer-head screws M 6 x 75

2 washers 6

2 wing nuts M6

Place fence rail onto the divider plate.

Position 1: for work with a higher contact

surface

Position 2: for work with a lower contact sur-

face

Place the cam lever on the guide slide horizon-

tally. Place the guide slide onto the guide pipe

and push the cam lever down - c!amp.

On the guide pipe, the upper scale applies to

position 1; the Iower scale to position 2.

Fence adjustment

Fig.“4“

Place the fence on the guide rail.

Place a straight strip on the sawband running

upwards and downwards.

Place an angle on the strip and on the fence.

Read the manual

Use hearing protection and protective

goggles

Only for EU countries

Do not dispose of electric tools with

household waste material!

In observance of european directive

2002/96/EC o wasted electrical and

electronic equipmet and its imple-

metation in accordance with national

law, electric tools that have reached

the end of their life must be collected

separately ad retured to an environ-

mentally compatible recycling facility.

Other Notes:

In these operating instructions we have

marked the places that have to do with

your safety with this sign: 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Basa 7.0 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info