Bedienungsanleitung Scheppach BS3000 Primaster (Seite 23 von 44) (Deutsch, Englisch, Französisch)

782175

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

23GB

• Make sure the blade guard (3) is in its lower posi-

tion when the saw is being transported.

• Safety guards are not to be used to move or mis-

use the machine.

• Blades that are misshapen or damaged in any way

must not be used.

• If the table insert is worn, replace it.

• Never operate the machine if either the door pro-

tecting the blade or the detachable safety device

are open.

• Ensure that the choice of blade and the selected

speed are suitable for the material to be cut.

• Do not begin cleaning the blade until it has come

to a complete standstill.

• For straight cuts of small workpieces against the

longitudinal limit stop the push stick has to be

used.

• The bandsaw blade guard should be in its lowest

position close to the bench during transport.

• For miter cuts when the table is tilted, the paral-

lel stop must be positioned on the lower part of

the table.

• When cutting round timber, use a suitable holding

device to prevent the workpiece turning.

• Never use guards to lift or transport items.

• Ensure that the bandsaw blade guards are used

and correctly adjusted.

• Keep your hands a safety distance away from the

bandsaw blade. Use a push stick for narrow cuts.

• The push stick has to be stored on the intended de-

vice, so that it can be reached from normal working

position and is always ready to be used.

• In the normal operating position the operator is in

front of the machine.

6. Technical data

Electro motor 220 - 240 V ~, 50 Hz

Power 750W

Revolutions 1400 min-1

Saw band length 2240 mm

Saw band width 12,5 mm

Saw band width max. 15 mm

Cutting speed 720 m/min

Passage height 360 m/min

Passage width 0 - 175 mm

Table size 305 mm

Slewing range of the table 500 x 400 mm

Max. size of the workpiece 0° bis 45°

Overall weight 600 x 600 x 175 mm

Gewicht 74 kg

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

The total noise values determined in accordance

with EN 61029.

sound pressure level LpA 77,4 dB(A)

uncertainty KpA 3 dB

sound power level LWA 90,4 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Total vibration values (vector sum - three directions)

determined in accordance with EN 61029.

7. Remaining hazards

The machine has been built using modern technolo-

gy in accordance with recognized safety rules. Some

remaining hazards, however, may still exist.

• Risk of injury for ngers and hands by the rotating

saw band due to improper handling of the work

piece.

• Risk of injury through the hurling work piece due

to improper handling, such as working without the

push stick.

• Risk of damaging your health due to wood dust and

wood chips. Wear personal protective cloth such

as goggles. Use a tting dust extractor.

• Risk of injury due to defective saw band. Regu-

larely check saw band for such defects.

• Risk of injury for ngers and hands while changing

saw band. Wear proper gloves.

• Risk of injury due to starting saw band while

switching on the machine.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Wear only closetting clothes. Remove rings,

bracelets and other jewelry.

• For the safety of long hair, wear a cap or hair net.

Even when all safety measures are taken, some

remaining hazards which are not yet evident may

still be present.

• Remaining hazards can be minimized by follow-

ing the instructions in „General safety instructions“

„Proper Use“ and in the entire operating manual.

8. Attachment and operation

Before starting the equipment

Make sure the machine stands securely, i.e. bolt it

to a workbench or solid base. There are two holes

for this purpose in the machine foot. • The saw table

must be mounted correctly.

• All covers and safety devices have to be properly

tted before the machine is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws etc.

• Before you actuate the On/Off switch, make sure

that the saw blade is correctly tted and that the

machine’s moving parts run smoothly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS3000 Primaster Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info