Bedienungsanleitung Scheppach BSH400 (Seite 17 von 28) (Deutsch, Englisch, Italienisch)

782178

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

english

Assembly

Assembly tools

Blade key

Holding mandril

Hex pin wrench (Wrench size 5 / 6 included in delivery)

Open-end wrench (Wrench size 7, 8, 10, 13, 17)

Screw driver not included in delivery

Due to technical packing reasons, your scheppach machine

does not come completely assembled.

Lower saw blade cover, clamp angle, Fig. 01

•

Screw the pivoting bracket (1) onto the adjustment

frame in the following order.

Large washer

Pivoting bracket (1)

Small washer ø 8

Hex nut M8 self-locking

•

The pivoting bracket must be freely moveable.

•

Screw together screw down cover (2) and guard plate

(3).

3 cheese-head screws M 4 x 10

3 serrated edge washers A 4.3

3 hex nuts M4

•

Screw on guard plate (3) and pivoting bracket (1).

4 hex bolts M6x12

4 serrated edge washers A 6.4

4 hex nut M6

•

Attach both clamp angles (4)

4 hex bolts M8x 12

4 serrated edge washers A 8.4

Hand wheel, Switch unit, Switch plug combination, Fig. 02

Screw the hand wheel onto the adjusting spindle.

1 washer 8

1 cap nut M8

Switch unit 400 V

1 hex bolt M8 x 16

1 serrated edge washer A8.4

1 hex nut M8

Switch plug combination three-phase

2 raised-head screws M 4 x 50

2 washers ø 4

2 serrated edge washers A 4.3

2 hex nuts M 4

Frame legs, Cross-cutting guide, Fig. 03

•

Insert frame legs with spacing angle (5) into the table

corners and adjust the screws loosely.

each 1 cheese-head screw M8 x 100

each 1  ller piece (6)

each 1 stay piece (7)

each 1 serrated edge washer A 8,4

each 1 hex nut M8

as well as

each 2 carriage bolts M8 x 60 with serrated washers and

hex nuts.

Make sure to attach the cross-cutting guide onto the right side

of the table at the same time.

•

Slide the rubber ring (8) and the cross-cutting guide

onto the guide rail.

Screw the front bracket (9) onto the guide rail.

1 serrated edge washer 10.5

1 hex nut M10

Insert the rear bracket (11) onto the guide rail.

U-bolts

•

Attach both U-bolts (10) diagonally to each other.

each 2 serrated edge washers 10.5

each 4 hex nuts M10

Longitudinal and diagonal braces, Fig. 04

Note insertion position as it corresponds to the diagonal

position of the frame legs.

•

First attach the braces lightly with screws

each 1 cheese-head screw M8 x 45

each 1  ller piece (6)

each 1 brace clamp (11)

each 1 serrated edge washer 8.4

each 1 hex nut M8

Then tighten all screws and nuts on the frame legs and

braces. Place the machine on its legs.

Clamping attachment for ripping fence, Fig. 05

•

Attach the clamping attchment (1) for the ripping

fence

2 cheese-hex screws M6 x 30

2 serrated edge washers 6,4

2 hex nuts M6

Cross-cutting guide, Fig. 05

•

Insert a carriage bolt M8 x 70 from beneath the rect-

angular tube into the cross-cutting guide. Clamp the

cross-cutting guide with washer 8 and the hand wheel.

With the hex bolt in the rectangular tube, adjust the

swivel component at a right angle to the saw blade.

Noise parameters

The noise emission values at the work place, determined

according to EN 23746 (acoustic power levels) and EN

31202 (acoustic pressure levels) with a correction factor

k3 calculated according to appendix A.2 of EN 31204,

based on operating conditions listed in ISO 7904,

appendix A, are:

bsh 400

Acoustic power level in dB

Idling L

= 93.9 dB(A) Operating L

= 101.8 dB(A)

Acoustic pressure level in dB

Idling L

pAeq

= 79.7 dB(A) Operating L

pAeq

= 91.3 dB(A)

bsh 500

Acoustic power level in dB

Idling L

= 100.7 dB(A) Operating L

= 108.3 dB(A)

Acoustic pressure level in dB

Idling L

pAeq

= 88.3 dB(A) Operating L

pAeq

= 95.8 dB(A)

A measuring uncertainty coef cient (K = 4 dB) applies to

the emission values listed above.

Dust emmision parameters

The dust emmision parameters, measured according to the

principles for measuring dust emmisions (concentration

parameter) for woodworking machines speci ed by the

German wood professional committee, are below 2 mg/m

Dust emmissions can therefore be continuously kept

within the range allowed under currently valid German

regulations by connecting the machine to a vacuum ex-

haust system with an air ow speed of at least 20 m/s.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BSH400 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info