Bedienungsanleitung Scheppach CAG115-20ProS (Seite 27 von 92) (Deutsch, Englisch, Französisch, Polnisch)

781689

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 27

For grinding or cutting wheels up to approx. 3

mm thick: Screw on the ange nut with the at side

facing the grinding or cutting wheel.

10.3.2 Flange arrangements when using grinding

wheels and cutting wheels (Fig. 5)

• Mount guard (1), clamping ange (a), wheel (7) and

ange nut (b) as shown in Fig. 5.

• The arrows indicate the mounting direction.

10.4 Motor

It is vital for the motor to be well ventilated during op-

eration. Be sure, therefore, to keep the ventilation

holes clean at all times.

10.5 Grinding wheels

• Never use a grinding or cutting wheel bigger than

the specied diameter.

• Before using a grinding or cutting wheel, check its

rated speed.

• The maximum speed of the grinding or cutting

wheel used must be higher than the idle speed of

the angle grinder.

• Use only grinding and cutting wheels that are ap-

proved for a minimum speed of 8,500 rpm and a

peripheral speed of 52 m/sec.

• Check the direction of rotation when you use dia-

mond cutting wheels. The directional arrow on the

diamond cutting wheel must point in the direction

in which the tool rotates.

Take special care that the grinding/cutting wheels

are properly stored and transported. Ensure that the

grinding/cutting wheels are never exposed to shock,

jolts or sharp edges (for example during transport

or storage in a toolbox). This could cause damage

(such as cracks) to the grinding/cutting wheels and

place the user in serious danger.

11. Operating instructions

When working with the device, always wear suit-

able clothing and appropriate protective equip-

ment. Prior to each use it must be ensured that

the device is working correctly. Personal protec-

tive equipment and a fully functional device re-

duce the risk of injuries and accidents.

11.1 Rough grinding

m WARNING

Use the safety device for grinding

For the best rough grinding results, hold the grind-

ing wheel at an angle of between 30° and 40° to the

workpiece surface and guide back and forth over the

workpiece in steady movements.

11.2 Cutting

m WARNING

Use the safety device for abrasive cutting

When you use the right-angle grinder for cutting pur-

poses, avoid tilting it in the cutting plane. The cutting

wheel must have a clean cutting edge. A diamond

cutting wheel is best used to cut hard stone.

m It is prohibited to use the machine on asbes-

tos materials!

m Never use a cutting wheel for rough grinding.

12. Cleaning, storage and

maintenance

m WARNING

Always pull out the battery pack before starting

any cleaning work.

12.1 Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric tool

increases the risk of an electric shock.

12.2 Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C. Store the electrical tool in its original packag-

ing. Cover the electrical tool in order to protect it from

dust and moisture. Store the operating manual with

the electrical tool.

12.3 Maintenance

There are no parts inside the equipment which re-

quire additional maintenance.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: Grinding wheels

* Not necessarily included in the scope of delivery!

13. Disposal and recycling

The equipment is supplied in packaging to prevent it

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CAG115-20ProS Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info