Bedienungsanleitung Scheppach CSE2400 (Seite 32 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

781698

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

32 GB

• Keep the cooling vents on the motor housing clean

and unobstructed at all times.

• Only the maintenance work described in these

operating instructions may be carried out. Any

other maintenance work must be carried out by our

Customer Service.

• Do not modify the power saw in any way as this

could jeopardize its safety.

• Should the chainsaw fail despite our careful

manufacturing and inspection procedures, have it

repaired by an authorized Customer Service work-shop.

Filling in chain oil

To prevent dirt getting inside the tank, clean the oil

tank cap (21) before opening. Check the contents of

the oil tank during sawing work by checking the oil

gauge (15). Close the oil tank cap tightly and wipe

away any spills.

Sharpening the saw chain

You can have your saw chain sharpened fast and

correctly by specialist dealers, from whom you can

also obtain chain sharpening equipment to enable

you to sharpen the chain yourself.

Please follow the corresponding operating

instructions.

Take care of your tools. Keep your tools sharp and

clean to enable you to work well and safely.

Follow the maintenance regulations and the

instructions for changing tools

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the

following parts are therefore also required for use as

consumables. Wear parts*:

• saw chain

• guide bar

• chain oil

• carbon brushes

• claw stop

* Not necessarily included in the scope of delivery!

11. Storage

• Before every transport and storage, attach the

chain guard.

• Store the device in a dry place beyond the reach

of children.

• When the device is not being used, store it so it

cannot be started by unauthorised persons.

Warning!

Do not store the device without protection outside or

in a damp environment.

12. Electrical Connection

The installed electric motor is connected and is ready

to work.

• Watch out for spring backs. Use extreme caution

when cutting small size limbs. Pliable material

may catch in the saw chain and be whipped

toward you or pull you off balance.

• Watch out for spring backs. This is especially

true for branches that are bent or under pressure.

Avoid coming in contact with the branch or the

saw when there is tension in the wood.

• Keep your work area clear. Keep the path clear

of branches to avoid tripping over them.

Lopping (Fig.J)

• Lopping means removing branches from the

felled tree.

• Leave the larger limbs that are underneath the

felled tree, and use them as support while you

continue to work.

• Start at the base of the felled tree and work your

way up to the top. Remove smaller parts of the

tree with a cut in the direction of growth (arrows

Fig. J).

• Be sure to keep the tree between you and the saw.

• Remove larger, supporting branches using

the methods in the section „Bucking without

restraints“.

• Always cut branches under tension from the

underneath to the top, so the saw does not

become trapped.

• Always cut small and freely hanging limbs with

one cut. By undercutting they could fall in and

pinch the saw.

Trimming (Fig. I)

Attention: Leave stubs in branches or below cut

them to shoulder level only. Never cut branches

above shoulder height. Leave such work to an expert.

• Make the rst cut (Item 1) 1/3 in the bottom of

the limb.

• Then cut the second section (Item 2) all the way

through the branch. The third section (item 3) is

a general section that allows you to separate the

branch at 2.5 to 5 cm from the trunk.

Sawing on a slope (Fig. K)

When sawing on a slope, make sure you always

stand higher than the tree trunk (Fig. K). In order to

maintain complete control at the moment of “sawing

through”, reduce pressure towards the end of the

cut without releasing your tight grip on the handles

of the chainsaw.

Warning!: The saw chain must not come in contact

with the ground..

After completing the cut, wait for the saw chain to

come to a standstill before removing the chainsaw.

Always turn off the chainsaw’s motor when going

from one tree to the next.

10. Maintenance

Always pull the plug out of the power socket before

doing any work on the chainsaw!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CSE2400 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info