Bedienungsanleitung Scheppach Deco 401 (Seite 10 von 92) (Alle Sprachen)

782185

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

english 11

maining hazards which are not yet evident may still be

present.

• Remaininghazardscanbeminimizedbyfollowingthe

instructionsin„SafetyPrecautions“,„ProperUse“and

in the entire operating manual.

• Donotforcethemachineunnecessarily:excessivecutt

ing pressure may lead to rapid deterioration of the blade

anda decreasein performance in terms of nish and

cutting precision.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

Scroll Saw Design Features, Fig. 1

1 Quick release and tension lever: forquicktensioningand

removalot the saw blade with a handle on the lever.

2 Blade guard: protects your hands from injury.

3 Work piece holder

4 Shavings blower: keeps the workpiece area free from

dust.

5 decotronic: electronical speed switch

deco 402: Speed switch

6 On/Off switch

7 Angle scale: you can read the angle position of the table

with this scale.

Installation

Setting the saw bench, Fig. 2

Setting the angle scale

• Releasethestarbuttonandbringthesawbench(2)toa

rightangle(3)inrelationtothesawblade.

• Use a 90° angle tc measure the right angle between

thebladeandthebench.Thesawbladebe90°tothe

angle.

• Closethestarbuttonagainwhenthedistancebetween

thebladeandthe90°angleisataminimum.Thebench

shouldthenbeat90°tothesawblade.

• Releasethe lockscrew andbringthe indicatorto the

zero position. Fasten the screw. Please note: the angle

scaleisausefulpieceofsupplementaryequipment,but

should not be used for precision work. Use scrap wood

for saw tests, adjust the bench if neces sary.

Note: The bench should not be on the motor block, this can

cause undesireable noise.

Horizontal saw bench and diagonal cuts, Fig. 2+3

• Thesawbenchcanbepositionedintoa450diagonal

position or be left in the horizontal position.

• Youcanreadofftheapproximateslopeanglebyusing

the angle scale located under the work bench. For more

exact adjustment, use scrap wood for some saw tests;

adjust the bench if necessary.

Blade guard assembly, Fig. 4

Install the blade guard to the holder as shown in the dia-

gram. Secure the screws with a nut and washer.

• Liftthesawontotheframeandbaseandpushitonto

the workbench.

• Familiarizeyourselfwiththesawoperatingelementsand

features.

Mounting the saw on a work bench, Fig. 5

• Aworkbenchmadefromsolidwoodisbetierthanone

made of plywood, as interfering vibrations and noise are

more noticeable with plywood.

• Thenecessarytoolsandsmallpartsforassemblingthe

saw on a workbench are not supplied with the saw. How-

ever,useequipmentofatleastthefollowingsize:

1 Saw body

2 Foam rubber base

3 Work bench

4 Flat seal

5 Washer

6 Hexagonal nut

 7Locknut

8 Hexagonal bolt

Ouantity Description

 4Hexagonalbolts(6mm)1/420xlength

 4Flatseal(7mm)9/321.0

 4Washers(7mm)9/321.0.

 8Hexagonalnuts(6mm)1/420

First of all, drill holes into the seating surface and then

insert the screws.

• Afoamrubberbaseforreductionofnoiseisnotsupplied

with the saw either. However, we expressly recommend

that you use such a base to keep vibration and noise to

a minimum. Ideal size 410 x 320 mm.

Changing the saw blades

Warning: Switch off the saw and remove the mains supply plug

before installing saw b!ades in order to avoid injuries caused

by unintentiona! activation of the saw.

A. Flat saw blades

A.1 Removing the saw blades, Fig. 7

1 First af all, release the tension via the tensianing tap ta

remave the saw blade.

2Undothescrewsetontheupperbladeholder(Fig.8).

3 Undo the lower holder. To do this, use the spanner which

you can feed through the saw blade slot.

4Removethesawbladebypullingitforwards fromthe

holders and by pulling it through the access hole in the

bench(Fig.9).

A.2 lnstalling the saw blade

1Wheninstallingthesawblade,rstofallpullitthrough

the saw blade slot in the work bench.

Note: In order to avoid tearing or lifting of lightweight work-

pieces, the saw blade teeth should always face down towards

the work bench.

2 Guide the saw blade into the lower holder and fasten the

screws(Fig.9).

3 Guide the other end of the blade into upper holder and

fasten the screws. Push the upper arm of the saw slight-

lydownwardsbeforetighteningthescrews(Fig.10).

4 Tension the blade by turning the tensioning tap clock-

wise.Checkthebladetension.Carryonturningclock-

wisetotensionthebladefurther(Fig.11).

Note: It is difﬁcult to open the tensioning tap again if the blade

is too tightly tensioned.

Saw blade with pins

Note: The upper and lower holders should not be tightened

too much when using saw blades which have pins. The gap

between the holding blocks must be slightly wider than the

saw blade. After installation, the blade is held in place by the

tensioning device.

B.1 Removing the saw blade, Fig. 7

1 First of all, release the tension tap.

2 Take the saw blade out from the upper and lower holder.

Push the upper arm of the saw slightly downwards be-

fore tightening the screws.

B.2 Installing the saw blade

1 Guide one end of the saw blade through the borehole in

Scheppach Deco 401 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info