Bedienungsanleitung Scheppach DECO-XLS (Seite 34 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

781462

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

www.scheppach.com

34 | GB

12.2.2 Carbon brushes

In case of excessive sparking, have the carbon brush-

es checked only by a qualied electrician.

IMPORTANT

The carbon brushes should not be replaced by anyone

but a qualied electrician.

12.2.3 Mains cable

If the mains cable is pulled out, cut, or damaged in

some other form, then it should be replaced immedi-

ately.

12.2.4 Replacing the ne-wire fuse (g. 16)

If the ne-wire fuse (36) is defective, it must be re-

placed with a ne-wire fuse of the same type.

WARNING

Do not bypass the ne-wire fuse (36)! Do not use fus-

es of any other type! This can lead to damage to the

device.

12.3 Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the following

parts are therefore also required for use as consum-

ables.

Wear parts*: Carbon brushes, saw blade, table inlay

* Not necessarily included in the scope of delivery!

Spare parts and accessories can be obtained from our

service centre. To do this, scan the QR code on the

cover page.

12.4 Ordering replacement parts

The following information must be provided on all or-

ders for spare parts:

• Device type

• Device article number

13. Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing temper-

ature. The ideal storage temperature is between 5 and

30 °C. Store the electric tool in its original packaging.

11. Transport

• Transport the electric tool by lifting it on the recesses

provided for this on the frame and the engine cover.

• Never use the protective devices for handling or

transport.

• Make sure that the exposed part of the saw blade

is covered during transport, e. g. by the protective

device.

12. Cleaning, maintenance, storage

and ordering of spare parts

WARNING

Always switch the machine o󰀨 and remove the mains

plug prior to all maintenance and cleaning work.

12.1 Cleaning

Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. We recom-

mend that you clean the equipment immediately after

you use it.

12.1.1 Exterior cleaning

• Clean the equipment regularly with a damp cloth and

some soft soap.

• Do not use cleaning agents or solvents; these may

be aggressive to the plastic parts in the equipment.

• Ensure that no water can get into the interior of the

equipment.

12.1.2 Interior cleaning (g. 15)

1. Open the storage box (9).

2. Remove the screw (35).

3. Loosen the screw (34).

4. Remove the cover (8).

5. Blow out the device interior with low-pressure

compressed air.

6. Attach the cover again (8).

7. Fasten the screw (34).

8. Insert the screw (35) again and tighten it.

9. Close the storage box (9).

12.2 Servicing

12.2.1 Bearings (g. 1/pos. 10)

Lubricate the bearing points (10) of the deection roll-

ers after approx. 25-30 operating hours at the latest

using high-quality machine grease.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DECO-XLS Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info