Bedienungsanleitung Scheppach DH1000PLUS (Seite 13 von 44) (Deutsch, Englisch, Französisch, Polnisch)

781874

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

13 І 44

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

not be used without the additional handle (8) for safety

reasons. The additional handle (8) is secured to the

hammer drill by a clamp. Turning the handle anticlock-

wise (looking from the handle) will release the clamp.

Turning the handle clockwise will tighten the clamp. First

release the additional handle clamp. You can then swing

the additional handle (8) into the most comfortable

working position for you. Now turn the additional handle

in the opposite direction again until the additional handle

is secure.

Tiefenanschlag (Fig. 3 – Item.9)

The depth stop (9) is held in place with the locking

screw (A) on the additional handle (8) by means of a

clamp.

• Undo the locking screw (A) and t the depth stop (9).

• Set the depth stop (9) to the same level as the drill bit.

• Pull the depth stop (9) back by the required drilling

depth.

• Retighten the locking screw (A).

• Now drill the hole until the depth stop (9) touches the

workpiece.

Tool insertion (Fig. 4)

• Clean the tool before insertion and apply a thin coa-

ting of drill bit grease to the shaft of the tool.

• Pull back and hold the locking sleeve (2).

• Insert the dust-free tool into the tool mounting as far

as it will go whilst turning it. The tool will lock itself.

• Check that it is properly secure by pulling the tool.

Tool removal (Fig. 5)

Pull back and hold the locking sleeve (2) and remove

the tool.

Dust collection device (Fig. 6)

Slide the dust collection device (B) over the drill bit

before carrying out any hammer drilling vertically above

your head.

Operation

Danger

To prevent all danger, the machine must only be

held using the two handles (5/8). Otherwise there may

be a risk of suff ering an electric shock if you drill into

cables.

Status indicator (Fig.1)

The status indicator (6) lights up when the power plug is

connected.

Switching On and Off (Fig.1)

To switch on: Press and hold the operating switch (4).

To switch off : Let go of the operating switch (4)

Button hammer drilling / chiselling (Fig. 7)

• For hammer drilling, press the button (D) on the rotary

switch (3) and simultaneously turn the rotary switch

(3) to position E.

• For chiseling, press the button (D) on the rotary switch

(3) and simultaneously turn the rotary switch (3) to

position F. In switch position F the chisel is not locked.

• For chiseling, press the button (D) on the rotary switch

(3) and simultaneously turn the rotary switch (3) to

position G. The chisel is locked in position G.

Notice!

Only low pressure is required for hammer drilling. Ex-

cessive pressure will exert an unnecessary force on the

motor. Check the drill bits at regular intervals. Sharpen

or replace blunt drill bits.

Danger!

Sound and vibration

Sound and vibration values were measured in accordance

with EN 60745.

LpA sound pressure level 90.9 dB(A)

KpA uncertainty 3 dB(A)

LWA sound power level 101.9 dB(A)

KWA uncertainty 3 dB(A)

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 60745.

Main handle

Hammer drilling in

Concrete: ah(HD) = 13.59 m/s2, K = 1.5 m/s2

Additional handle

Hammer drilling in

Concrete: ah(HD) = 11.265 m/s2, K = 1.5 m/s2

Main handle

Chiselling: ah(CHeq) = 14.3 m/s2, K = 1.5 m/s2

Additional handle

Chiselling: ah(CHeq) = 14.51 m/s2, K = 1.5 m/s2

The specied vibration value was established in

accordance with a standardized testing method. It may

change according to how the electric equipment is used

and may exceed the specied value in exceptional

circumstances.

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect working

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical

to the mains data.

Warning!

Always pull the power plug before making adjust-

ments to the equipment.

Check the drilling point for concealed electrical cables,

gas and water pipes using a cable/pipe detector.

Additional handle (Fig. 2 – Item 8)

For safety reasons you must only use the hammer

drill with the additional handle.

The additional handle (8) enables you to achieve better

stability whilst using the hammer drill. The machine must

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DH1000PLUS Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info