Bedienungsanleitung Scheppach DM460T (Seite 11 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

782073

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

english 11

A measuring uncertainty coefcient (K = 3 dB) ap-

plies to the emission values listed above.

Subject to technical modications!

Controls and features (Fig. 1.1)

1. Headstock

2. Face plate

3. Tool rest with eccentric clamping and release

handle

4. Tailstock tip

5. Carrier

6. Tailstock

7. Eccentric release handle (on the back of the tail-

stock)

8. Drilling bed

9. On/off switch

10. Lever and binding screw

m General Safety Notes

• Please pass on safety notes and instructions to all

those who work on the machine.

• Comply with all safety instructions and warnings on

the machine.

• Keep all safety instructions and warnings on the ma-

chine fully legible.

• Check all power supply lines. Do not use defective

lines.

• Make sure that the machine stands stable on rm

ground.

• Caution when working: There is a danger to ngers,

hands and eyes.

• Keep children away from the machine when it is

connected to the power supply.

• When working on the machine, all safety mecha-

nisms and covers must be mounted.

• Operating personal must be at least 18 years of age.

Trainees must be at least 16 years of age, but may

only operate the machine under adult supervision.

• Persons working on the machine may not be divert-

ed from their work.

• The working space on the machine must be free of

chips and wood scrap.

• Wear only closetting clothes. Remove rings,

bracelets and other jewelry.

• For the safety of long hair, wear a cap or hair net.

• Do not wear gloves.

• Wear goggles when working.

• Note the motor rotational direction – see electrical

connection.

• The safety mechanisms on the machine may not be

removed or rendered unusable.

• Cleaning, changing, calibrating, and setting of the

machine may only be carried out when the motor is

switched off. Pull the power supply plug and wait for

the rotating tool to completely stop.

• Switch the machine off and pull power supply plug

when rectifying any malfunctions.

• Connection and repair work on the electrical instal-

lation may be carried out by a qualied electrician

only.

• All protection and safety devices must be replaced

after completing repair and maintenance proce-

dures.

• Place the tool support as tightly as possible against

the work piece.

• The peripheral speed of wooden workpieces must

not exceed 30 m/s. Note spindle speed diagram!

• Provide work pieces with center bores before clamp-

ing between pivots.

• Work large and imbalanced work pieces at a re-

duced rotational speed; it may be necessary before-

hand to cut accordingly with a band saw.

• Before switching on the machine, check that the

workpiece is securely clamped.

• Remove the chuck key or spring dowel sleeve be-

fore turning the machine on.

• Always close the belt cover.

• Work with three- or four-jaw chucks may only be

carried out with mounted jaw chuck shield.

• Never stop work pieces with the hand during run

out. Never take measurements on a rotating work

piece.

• Work only with well sharpened tools.

• Always use both hands when using turning tool.

• Nicked tools may not be used.

• Note the correct rotational setting on the machine.

• When leaving the work place, switch the motor off.

Pull the power supply plug.

• Unplug the machine before moving, even if only

slightly. Correctly connect the machine to the elec-

trical source before operating again.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair ac-

tive or passive medical implants under certain condi-

tions. In order to prevent the risk of serious or deadly

injuries, we recommend that persons with medical

implants consult with their physician and the manu-

facturer of the medical implant prior to operating the

electric tool.

Proper use

• CE tested machines meet all valid EC machine

guidelines as well as all relevent guidelines for each

machine.

• The machine must only be used in technically per-

fect condition in accordance with its designated use

and the instructions set out in the operating manual,

and only by safety-conscious persons who are fully

aware of the risks involved in oerating the machine.

Any functional disorders, especially those affecting

the safety of the machine, sholud terefore be recti-

ed immediately.

• The machine has been constructed exclusively for

use with wood.

• Any other use exceeds authorization. The manufac-

turer is not responsible for any damages resulting

from unauthorized use; risk is the sole responsibility

of the operator.

• The safety, work and maintenance instructions of

the manufacturer as well as the technical data given

in the calibrations and dimensions must be adhered

to.

• Relevant accident prevention regulations and other,

generally recognized safety-technical rules must

also be adhered to.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DM460T Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info