Bedienungsanleitung Scheppach DM460T (Seite 14 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

782073

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

14 english

Such defective electrical connection cables must not

be used as the insulation damage makes them ex-

tremely hazardous.

Check electrical connection cables regularly for dam-

age. Make sure the cable is disconnected from the

mains when checking.

Electrical connection cables must comply with the

regulations applicable in your country.

Single-phase motor, Fig. 06

• The mains voltage must coincide with the voltage

specied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have a

cross-section of 1.5 mm2, and beyond 25 m at least

2.5 mm2.

• The connection to the mains must be protected with

a 16 A slow-acting fuse.

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

If a motor has to be returned, it must always be dis-

patched with the complete driving unit and switch.

Maintenance

• Overhauls, maintenance work, cleaning, as well as

the elimination of any malfunctions must only be un-

dertaken after turning off the motor.

• All protective and safety equipment must be rein-

stalled immediately upon completion of any repair

or maintenance work.

• Clean and lightly oil the spindle thread of the tool

holder when changing tools.

• When possible, the tail stock sleeve should be re-

moved by unscrewing it, cleaned and then sprayed

with a dry lubricant. Grease the threaded spindle.

• Check the eccentric clamp of the tailstock as well as

the tool holder and adjust if necessary. In addition,

tighten the hex nut under the bracket.

• Check the drive belt and replace when necessary.

Accessories

Article Art. No.

Turning lathe extension 4902301701

Additional tools 5er set 88002716

Additional tools 6er set 88002717

Screw chuck 7400 7200

Socket chuck Ø 30 mm 7400 8600

Socket chuck Ø 40 mm 7400 7300

Socket chuck Ø 60 mm 7400 8700

Driver plate Ø 80 mm 7400 8800

Three-jaw chuck Ø 100 mm 7400 8900

Four-jaw chuck Ø 125 mm 7400 7400

Drill chuck 3 – 16 mm cone mandrel MK-2 7400

7700

You can nd other accessories in our current cata-

logue or at www.scheppach.com.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the follow-

ing parts are therefore also required for use as con-

sumables.

Wear parts*: Carbon brushes, v-belt

* Not necessarily included in the scope of delivery!

Disposal and recycling

The equipment is supplied in packaging to prevent it

from being damaged in transit. The raw materials in

this packaging can be reused or recycled. The equip-

ment and its accessories are made of various types

of material, such as metal and plastic. Defective com-

ponents must be disposed of as special waste. Ask

your dealer or your local council.

Old devices must not be disposed of with house-

hold waste!

This symbol indicates that this product must

not be disposed of together with domestic

waste in compliance with the Directive

(2012/19/EU) pertaining to waste electrical and

electronic equipment (WEEE). This product must be

disposed of at a designated collection point. This can

occur, for example, by handing it in at an authorised

collecting point for the recycling of waste electrical

and electronic equipment. Improper handling of waste

equipment may have negative consequences for the

environment and human health due to potentially haz-

ardous substances that are often contained in electri-

cal and electronic equipment. By properly disposing

of this product, you are also contributing to the effec-

tive use of natural resources. You can obtain informa-

tion on collection points for waste equipment from

your municipal administration, public waste disposal

authority, an authorised body for the disposal of

waste electrical and electronic equipment or your

waste disposal company.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DM460T Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info