Bedienungsanleitung Scheppach DMS 1200 Vario (Seite 14 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

782104

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

english 13

• Turn the workpiece by hand to check if it rests se-

cured.

Marking of the workpiece, ﬁgure 17

Sometimes the workpiece has to be taken out before it has

been completed. It is advantageous to mark the workpiece

and the driver with a pencil ﬁrst.

When placing the workpiece back in the machine, match

the marks on the workpiece and the driver.

By means of the spindle locking bolt (E1), you can lock

the spindle.

12 screenings with respectively 30° are possible by mark-

ing out.

Specialized literature

Specialized shops offer appropriate specialized literature

about wood turning. They can be a great help for begin-

ners in their work as well as a source of ideas for experts.

m Electrical connection

The installed electric motor is completely wired ready for

operation.

The customer’s connection to the power supply system,

and any extension cables that may be used, must conform

with local regulations.

Important remark:

The motor is automatically switched off in the event of an

overload. The motor can be switched on again after a cool-

ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinks resulting from incorrect attachment or laying of

the connection cable.

• Cuts resulting from running over the connecting ca-

ble.

• Insulation damage resulting from forcefully pulling out

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely haz-

ardous.

Check electrical connection cables regularly for damage.

Make sure the cable is disconnected from the mains when

checking.

Electrical connection cables must comply with the regula-

tions applicable in your country.

Single-phase motor

• The mains voltage must coincide with the voltage speci-

ﬁed on the motor’s rating plate.

• Extension cables up to a length of 25 m must have a

cross-section of 1.5 mm2, and beyond 25 m at least

2.5 mm2.

• The connection to the mains must be protected with a

16 A slow-acting fuse.

Only a qualiﬁed electrician is permitted to connect the ma-

chine and complete repairs on its electrical equipment.

In the event of enquiries please specify the following da-

ta:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

If a motor has to be returned, it must always be dispatched

with the complete driving unit and switch.

Maintenance

• Overhauls, maintenance work, cleaning, as well as the

elimination of any malfunctions must only be under-

taken after turning off the motor.

• All protective and safety equipment must be reinstalled

immediately upon completion of any repair or mainte-

nance work.

• Clean and lightly oil the spindle thread of the tool hold-

er when changing tools.

• When possible, the tail stock sleeve should be removed

by unscrewing it, cleaned and then sprayed with a dry

lubricant. Grease the threaded spindle.

• Check the eccentric clamp of the tailstock as well as

the tool holder and adjust if necessary. In addition,

tighten the hex nut under the bracket.

• Check the drive belt and replace when necessary.

Accessories

Jaw chuck protection Fig. 18

When working with the jaw chuck (accessory), the jaw

chuck protection must be used.

Extension console, Fig. 19

When working on a piece with a max. diameter of up to

500 mm, the extension console which is used must be at-

tached on the frontal side. Thereby, the headstock is re-

moved from the lathe bed, rotated by 180°, attached to

the lathe bed and refastened. The standard tool support is

employed here.

Article Art. No.

Screw chuck 7400 7200

Socket chuck Ø 30 mm 7400 8600

Socket chuck Ø 40 mm 7400 7300

Socket chuck Ø 60 mm 7400 8700

Driver plate Ø 80 mm 7400 8800

Three-jaw chuck Ø 100 mm 7400 8900

Four-jaw chuck Ø 125 mm 7400 7400

Extension console 8800 2756

Jaw chuck protection 8800 2758

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DMS 1200 Vario Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info